A 10-hp, 550V, 60 Hz, 3-phase induction motor has starting torque of 160 percent of full load torque and a starting current of 425 percent of full load current. What voltage is required to limit the starting current to the full load current value?

A 10-hp, 550V, 60 Hz, 3-phase induction motor has starting torque of 160 percent of full load torque and a starting current of 425 percent of full load current. What voltage is required to limit the starting current to the full load current value?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Related questions

Q: A 4-pole , 50hz , 7.46 kW induction motor has at rated voltage and frequency, a starting torque of…

Q: A 6-pole, 50hz, 3-phase induction motor has a fully load speed of 950 rpm. Its speed in Rpm at half…

Q: The efficiency of 3-ph induction motor. at (Is=4.5A, T=13 N.m, N=1333 rpm, Pph=864 watt ) is

A: The solution can be achieved as follows.

Q: A 4-pole induction motor (main) and a 6-pole motor (auxiliary) are connected in cumulative cascade.…

A: Given, a 4-pole induction motor (main) and a 6-pole motor (auxiliary) are connected in cumulative…

Q: What is the reason of the high starting current in the 3-phase induction motor? Explain in short.

A: Solution: The approximated equivalent circuit of the three-phase induction motor is, From the…

Q: A 380 V, 60 Hz, Star connected, 870 r.p.m., Eight poles, Three-Phase Induction Motor has the…

A: 380 line to line voltage, 60Hz frequency, 8 pole, 870rpm speed 3 phase induction motor parameters…

Q: A three-phase induction motor used for a commercial application in Oman runs at 580 rpm at no load…

A: Given: A three phase induction motor No load speed = 580 rpm Speed at full load = 552 rpm To…

Q: ationship between slip s) and load (Pa) in an induction motor? Please explain.

A: The induction motor is an AC motor. It rotates slightly less than synchronous speed. It is…

Concept explainers

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.

Question

A 10-hp, 550V, 60 Hz, 3-phase induction motor has starting torque of 160 percent of full load
torque and a starting current of 425 percent of full load current. What voltage is required to
limit the starting current to the full load current value?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An 8-pole, 50 Hz induction motor has a full load slip of 2.5 percent and amaximum torque of twice the full-load torque. At what value of slip does themaximum torque occur?
7- A 6-pole, 50-Hz, 3-0 induction motor is running at 950 rpm and has rotor Cu loss of 6 kW. Its rotor input is......kW (a) 120 (b) 60 (c) 6.3 (d) 66 8- The number of slip rings on a squirrel cage induction motor is usually (a)Two (b) Three (c) Four (d) None
Torque-speed characteristics for three phase induction motor 4. Discuss the following (rated torque, starting torque, break down torque).
Draw the typical speed-torque characteristic of the induction motor and expain it.
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
I need the answer as soon as possible
Q4) Is an induction motor self-starting? Clarify this on the Torque/Speed characteristics
A single-phase, 120 V, 60 Hz, four-pole, split-phase induction motor has the following standstill impedances:Main winding: Zm =5+j6.25Auxiliary winding: Za =8+j6a) Determine the value of capacitance to be added in series with the auxiliary winding to obtainmaximum starting torque.b) Compare the starting torques and starting current with and without the added capacitance in theauxiliary winding circuit when operated from a 120V, 60Hz supply
An 8 pole, 50 Hz slip ring induction motor runs at a slip of 2.67% on full load. The rotor resistance per phase of the winding is 0.2 ohm. What external resistance per phase must be added in the rotor circuit so that the motor now runs ate a slip of 17.33% such that the torque remains same in both the cases. (Ans: 1.1 ohm)
1.why the slip of induction motor is never zero, 2.what happens if the slip of induction motor is one, 3.what is the value of the slip for an induction motor at on load and full load
18. A single-phase, 120 V, 60 Hz, four-pole, split-phase induction motor has the following standstill impedances: Main winding: Zm =5+j6.25 Auxiliary winding: Za =8+j6 a) Determine the value of capacitance to be added in series with the auxiliary winding to obtain maximum starting torque. b) Compare the starting torques and starting current with and without the added capacitance in the auxiliary winding circuit when operated from a 120V, 60HZ supply.
Answer it right..