A 10-hp, 120-V, 1000 rpm shunt DC motor has a full load armature current of 70 A when operating at rated conditions. The armatureresistance of the motor, RA is 0.12 Q and the field resistance RF is 40 0. The adjustable resistance of the motor in the field circuit, Radimay be varied over the range from 0 to 200 Q and currently set at 100 Q. Armature reaction can be ignored in this machine.The magnetization curve for this motor, taken at a speed of 1000 rpm is summarized in the following table. Note that linear interpolationapplies when the value is not explicitly stated in the table.EA, V7895112118126IF, A0.000.801.001.281.442.88If the motor is now unloaded with no changes in terminal voltage or Radj, how much is the increase in the no load speed of the motor?Hint: For linear interpolation in the interval, the formula to obtain the unknown point in this interval is as follows:Уo (х, — х) + у, (х — хо)y =X1 - Xo

Answered: Image /qna-images/answer/5a6fafe7-db0b-46b6-bfb7-c312b663b489.jpg

Answered: A 10-hp, 120-V, 1000 rpm shunt DC motor…

Engineering

Electrical Engineering

A 10-hp, 120-V, 1000 rpm shunt DC motor has a full load armature current

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A A permanent magnet DC motor has an armature resistance supplied by a 75-V DC Source, 1.4 S2. When it n svy t no-load speed d 2200 pm and draws 1.7 A. a) what 6.) What is the rotational'loss ? TS the output power (in hp) when it is operated at from 1800 rpm a 70-V DC source 7
Q18 / Draw The torque-speed characteristic of a series DC motor.
Qa/ a- Explain the difference in the Torque-Speed Characteristics of DC Shunt and series Motors. b+ A 120 V shunt motor has the following parameters: Ra = 0.4 0, RF = 120 Q. On full load, the tine current is 19.5 A and the motor runs at 1200 rpm, find the output torque.
A DC motor with a shunt field winding has the following characteristics: Vr = 96.0 V R = 1.50 Q K = 0.352 m Specify the flux required to achieve a starting torque of 18 Nm.
a 20kw, 200v dc shunt motor has an electrical efficiency of 86% and an armature resistance of 0.25ohms what is the value of shunt field resistance in ohms
A 2 hp 50 Hz 3-phase 220 V delta wired induction motor has a full-load rated speed of 1400 rpm. a) How many poles does the motor have? b) Calculate its rated output torque. c) What is the slip at full load? d) If the current is 6.37 A with a power factor of 0.79 at full load, what is the efficiency of the motor? e) Calculate the torque and approximate speed at ½ load. f) If a variable frequency drive were used to control the speed of this motor, what is the approximate maximum speed for the load from e)? What frequency would the drive be set to? Please answer all subpart either dislike is ready please all subpart in short please
The supply voltage to a DC motor is 160V. If the back emf Ez=155V and the armature resistance A6 is 0.250, the armature current is a) 5A b) 10A c) 15A d) 20A 1800 ro/min The frequency
A 550-volt long-shunt compound motor has armature an resistance of 0.815 ohm and a series field resistance of 0.15 ohm. The full load speed is 1,900 rpm when the armature current is 22 amp. (a) At what speed will the motor operate at no load if the armature current drops to 3 amp with a corresponding drop in flux to 88 per cent of the full-load value? (Assume a brush drop of 5 volts at full load and 2 volts at no load.) (b) Calculate the percent speed regulation of the motor.
A 440-V, shunt motor has armature resistance of 0.8 Q and field resistance of 200 Q. Determine the back emf when giving an output of 7.46 kW at 85 per cent efficiency.
An armature controlled DC motor has the following parameters: Tf = 0.03 Nm KT = 0.15 Nm/A Imax = 2.4 A KĘ = 0.15 Vs/rad Wmax = 5000 rpm R = 0.8 Ohms 1. Determine the following: (i) The maximum output torque. (ii) The maximum power output. (iii) The maximum armature voltage. (iv) The no load motor speed when e = Emax 2. Plot the following relationships: (i) Torque versus current (ii) Induced voltage versus speed 3. If the above motor is operated at 3000 rpm with a load torque of 0.15 N.m, determine the armature voltage
A 230 shunt motor has a nominal armature current of 60 A. If the armature resistance is 0.15 0. calculate The counter EMF
Q15. A series-wound motor is connected to a d.c. supply and develops full-load torque when the current is 30 A and speed is 1000 rev/min. If the flux per pole is proportional to the current flowing, find the current and speed at half full- load torque, when connected to the same supply.