A 1.35 meter high cylindrical tank is used in lifting oil to the top of the building. The allowable pressure at the bottom of the tank is 16 kPa. Determine the positive maximum vertical acceleration (2) that can be imposed in the cylinder when it is filled with oil.

A 1.35 meter high cylindrical tank is used in lifting oil to the top of the building. The allowable pressure at the bottom of the tank is 16 kPa. Determine the positive maximum vertical acceleration (2) that can be imposed in the cylinder when it is filled with oil.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A half parabolic gate 3m in tall and 1m wide is submerged and there are two different liquid on each…

A: Given- hg=3mb=1mGL=0.85GR=1.00

Q: pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank…

Q: A right circular tank 6 m. in diameter and 12 m. high is filled with 6 m. of oil sp. gr. = 0.80 and…

A: Diameter of tank = 6 m Initial Height of fluid = 12 m Diameter of orifice = 75 mm

Q: A rectangular tank 10m long by 2m deep by 5m wide contains Im of water. If the linear acceleration…

Q: Water in pressurized cylindrical tank 40 ft. in diameter discharges into the atmosphere through a…

A: D = 40 ftd = 4 in or 0.333 ft H1 = 50 ftH2 = 2 ft

Q: Q2:B) Calculate the power required to pull (1.5m x 1.5m) flat plate at speed (1 m/s) to the left…

Q: An open tank contains 9.4 ft of water beneath 1.8ft of oil with specific gravity of .85. Find the…

A: Pressure is given byP=Sγw×zS=Specific gravityγw=Unit weight of waterz=depth

Q: 1. Consider a spherical elevated water tank with a diameter of 30 feet. The top of the tank is 90…

Q: Fluid Mechanics Question

A: Given below solution Explanation:Step 1: Step 2: Step 3: Step 4:

Q: Q1. In a piston-cylinder assembly attached with spring load is filled with 60 kg of water at…

A: Given Data - m = 60 kgPi = 250 kpaTi = 25 °C = 298 KA = 0.1 m2 v2 = 0.2 m2k = 100 kN/mx = 20 cm

Q: A water pipe runs vertically through a tall building, with a flow rate of 0.2 m³/s. The diameter of…

Q: Current Attempt in Progress (Buoyancy, force on plane surface) A cube, 4.4 ft on a side, weighs 3110…

Q: Determine the positive maximum vertical acceleration () d with oil

A: Acceleration: - It is defined as the rate at which velocity of body changes with respect to time in…

Q: A closed cylindrical vessel of diameter 15 cm and length 100 cm contains water up to a height of 80…

A: D=15cm =0.15m Z=100cm=1m To find speed of rotation of vessel

Q: (Buoyancy, force on plane surface) A cube, 3.1 ft on a side, weighs 2870 lb and floats…

Q: 1. A closed cylindrical tank 1.50 in in radius and 2.5 in high is 3/4 full of oil (SG 0.90). If air…

A: Given Radius of cylindrical tank, R = 1.5 in Height of tank,H = 2.5 in Oil filled in…

Q: The center of a spherical water storage tank sits 31 m above ground level. The radius of the tank is…

A: Step 1: Determine the Volume of the Water to be Pumped into the TankThe tank is spherical with a…

Q: A square frame 3m by 3m in dimension is submerged in water vertically with its top 3 m form the…

A: Given datawe have a square frame of 3mx3m , submerged in water vertically with its top 3m from the…

Q: rectangular plate is submerged half in oil with a Gs = 0.8 and hald in water such that its top edge…

Q: I- A rectangular tank om long, 2.5m wide and 2m deep contains wader filled to Im deep. If the linear…

Q: We have a light pole given below. Assume the weight of the lamp is 200 kg (concentrated load) and…

Q: A closed cylindrical vessel is filled with water 3/4 of its height. The height is 4 meters and the…

A: Given data: Diameter of cylindrical vessel = D = 2 m Height of cylindrical vessel = H = 4 m…

Q: An open rectangular tank, 9.88 ft. high, 11.31 ft. long, and 3.21 ft wide, has liquid (SG = 1.12) to…

Q: a cylindrical tank is span at 300 rpm its axis vertical. the tank is 0.6 m high and 45cm diameter…

Q: 2. A closed vertical cylindrical vessel, 1.50m in diameter, 3m high is 8/10 full of liquid (SG=1.03)…

Q: In the figure shows a container having a width of 1.50 m. Calculate the total forces on the ends and…

A: Pressure and force are related, and so you can calculate one if you know the other by using the…

Q: An open rectangular tank, 9.88 ft. high, 11.31 ft. long, and 3.21 ft. wide, has liquid (SG = 1.12)…

Q: . A rectangular tank 2m long, 1.5m wide and 1.5m deep is filled with oil of specific gravity 0.8.…

Q: Two coaxial cylinders 250 mr high have a liquid in between them, the outer cylinder had internal…

Q: A 1.2m diameter open vessel, 2m high is filled with oil s.g = 0.85 at a depth of 1.6m and rotated at…

Q: An open cylindrical tank with a diameter of 37cm and 90cm high is partially filled with water. At…

Q: vertically into a body of water with open end down and floats with a 1300 N block of concrete (SG =…

A: D=350mm h=1.8m

Q: An open cylindrical tank 1.0m in diameter and 10 high contains water up to a height of 8m. If the…

Q: 6. The 5-1b package arrives at A, the top of the inclined roller conveyor, with a speed of 10 ft/s.…

Q: 2. If the velocity at point A is 25 meters per second, compute for the velocity at point C and the…

A: let pressure at point A is atmosphericthen gauge pressure pA=0elevation at A ZA=1+20=21 mand…

Q: An open rectangular tank, 9.62 ft. high, 11.29 ft. long, and 5.19 ft. wide, has liquid (SG = 0.53)…

A: Consider the following figure.

Q: A 1-m³ volume of water is contained in a rigid container. Estimate the change in the volume of the…

Q: .) For the tank shown below (width = 1.25 m), determine (6.a) the maximum horizontal acceleration…

Q: An open rectangular tank mounted on a truck is 5 m long, 2 m wide and 2.5 m high is filled with…

A: We will use formula of angle.

Q: 5-9 A 0.75-m³ rigid tank initially contains air whose den- sity is 1.18 kg/m³. The tank is connected…

A: Introduction: A rigid tank is an energy system that has rigid walls which contain saturated liquid…

Concept explainers

Thermal Processes

Some of the key areas where thermal processes find their application are:

Question

A 1.35 meter high cylindrical tank is used in
lifting oil to the top of the building. The
allowable pressure at the bottom of the
tank is 16 kPa. Determine the positive
maximum vertical acceleration (2) that can
be imposed in the cylinder when it is filled
with oil.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given Data

VIEW

Solution

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Civil engineering -Hydraulics
A cube container with a dimension of 3m on each side is 60% full of water (density=1000kg/m'). The cable elevator lifted it upwards with 25kN. Estimate the resulting pressure at the bottom of the tank in kilo Pascals.
3-160 A 5-m-long, 4-m-high tank contains 2.5-m-deep water when not in motion and is open to the atmosphere through a vent in the middle. The tank is now accelerated to the right on a level surface at 2 m/s2. Determine the maxi- mum pressure in the tank relative to the atmospheric pressure. Answer: 29.5 kPa 1.5 m 2.5 m Vent Water tank FIGURE P3-160 5 m 2 m/s2
An open tank filled with water and pulled at inclined surface as shown. Compute the acceleration which keeps the water surface at the position shown in fig. compute pressure at point(A) before and after acceleration. az ax 1.0m 1.40m A Static surface 3 Accelerated surface
Newt Scamander had caught a new magical sea creature. He wanted to know if the tank is strong enough because he can't use his magic for the mean time. Please refer to the front view details of the tank below. Neglecting atmospheric pressure. Compute the resultant force on the quarter-circle panel BC using 9.79kN/m^3 for the unit weight of water. 5m 3m ug
Homework 14 |A cylindrical vessel closed at the top and bo om is 300mm inn diameter, 1m long and contains water up to a depth of 0.8m. The air above the water surface is at a pressure of 60 KPa. If the vessel is rotated at a speed of 250n rpm about its ver cal axis, nd the pressure head at the bo om of the vessel at the center point and at the edge.
A piston 11.96 cm diameter and 14 cm long works in a cylinder 12 cm diameter. A lubricating oil which fills the space between them has Viscosity 0.65 poise. Calculate the speed at which the piston will move through the cylinder when an axial load of 0.86 kg is applied. Neglect the inertia of the piston. 1 14 cm VF- 0.86 Kgt
2- I want to answer this question. Thanks
Q2 The truck dumps water on the ground such that it flows from the truck through a 100-mm-wide opening at an angle of 60°. The length of the opening is 2 m. Determine the friction force that all the wheels of the truck must exert on the ground to keep the truck from moving at the instant the water depth in the truck is 1.75 m. 1.75 m
A tank 13 ft deep and 5 ft wide is layered with 6 ft of oil (y = 50.0 lbf/ft3), 5 ft of water, and 2 ft of mercury (y = 846 lbf/ft3). Compute (a) the total hydrostatic force and (b) the resultant center of pressure of the fluid on the right-hand side of the tank.