A 1.0-kW heater is constructed of a glass plate with an electrically conducting film that produces a constant heat flux. The plate is 60 cm by 60 cm and placed in an airstream at 27◦C, 1 atm with u =5 m/s. Calculate the average temperature difference along the plate.

A 1.0-kW heater is constructed of a glass plate with an electrically conducting film that produces a constant heat flux. The plate is 60 cm by 60 cm and placed in an airstream at 27◦C, 1 atm with u =5 m/s. Calculate the average temperature difference along the plate.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Related questions

Q: 4. A car engine with the dimensions 0.6 m high, 0.50 m-wide, and 0.8-m- long. The bottom surface of…

A: Data given-

Q: Air at 20◦C blows over a hot plate 50 by 75 cm maintained at 250◦C. The convection heat-transfer…

Q: A shock absorber with mass 0.2kg and heat capacity 500J/kg.K contracts by 0.19 meters due to an…

A: To calculate the heat expelled to the environment we will apply the law of conservation of energy.

Q: On a cold winter day, you decide to keep the outside surface windshield temperature at +2°C to…

Q: For a water flow over a steel surface, the temperature of water at a specific location was found to…

A: To find-: The local convection coefficient at this location. Given-: The temperature of water at a…

Q: A solar radiant heat flux of 700 W/m2 is absorbed in a metal plate that is perfectly insulated on…

A: Given : solar radiant heat flux, q' = 700 w/m2 convection heat transfer coefficient , h = 11 w/m2.…

Q: A room has a facade and openings according to the figure below and a continuous fire, fully…

A: Given: Let us consider the given data, Gas temperature,Tg=700°C Ambient temperature, Ta=20°C Ai=9…

Q: Air (its gas constant is 287 J/kg.k) escapes from a tank at a temperature of 55 C and specific…

Q: A steel radiant tube, that is 8 inches in diameter and 8 feet long, is placed inside of a convective…

Q: A. The temperature of a gas stream is to be measured by a thermocouple whose junction can be…

Q: A mass of 300kg of oil is cooled in 1 hour from 70 celcius to 35 celcius in a cooler consisting of a…

Q: Q5 Two large containers A and B of the same size are filled with different fluids. The fluids in…

Q: B-Water flows at Too 50 °C, hoo1 = 3500 W/m² ° C in a pipe with r₁= 1.25 cm, r₂ =1.33 cm and L= 1 m,…

Q: Calculate the rate of infiltration heat loss of a room with a 150m^2 floor area and 3.6m high…

A: The rate of infiltration heat loss from a room can be calculated using the formula:Rate of heat…

Q: Hot and cold liquid water are sent through a mixing chamber. The device is not insulated and the…

A: The given situation is of mixing chamber. That means some energy is coming in with two streams (hot…

Q: convection heat transfer

Q: Water at an average temperature of 23 deg C flows through a 10-cm diameter pipe that is 2.5 m long.…

A: Given: Tin = 23 deg C Diameter , D = 10-cm Length, L = 2.5 m long. Ts = 100 deg C. convective heat…

Q: A spherical container having an outer radius r2 and inner radius r1 (with thermal conductivity, k)…

Question

100%

Example 4: A 1.0-kW heater is constructed of a glass plate with an electrically conducting film that produces a constant heat flux. The plate is 60 cm by 60 cm and placed in an airstream at 27◦C, 1 atm with u =5 m/s. Calculate the average temperature difference along the plate.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Solution

VIEW

Step 3: Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel ball of density 7800 kg/m³ and specific heat 0.47 kJ/kg-K having 10 cm diameter at 300°C is placed in atmosphere at 30°C. Calculate the initial rate of cooling in °C/sec. Assume convective heat transfer coefficient h = 15W / (m ^ 2) - K . Neglect heat loss by radiation.
Air surrounding a light bulb is moving at 25 m/sec. The surrounding conditions are kept at atmospheric pressure and at temperature 25o C. The light bulb external surface is kept at 140o C. What is the heat transfer rate from the light bulb to the surrounding? Assume the light bulb as a sphere with a diameter of 50 mm.
How long should it take to boil an egg? Model the egg as a sphere with radius of 2.3 cm that has properties similar to water with a density of = 1000 kg/m3 and thermal conductivity of k = 0.606 Watts/(mC) and specific heat of c = 4182 J/(kg C). Suppose that an egg is fully cooked when the temperature at the center reaches 70 C. Initially the egg is taken out of the fridge at 4 C and placed in the boiling water at 100 C. Since the egg shell is very thin assume that it quickly reaches a temperature of 100 C. The protein in the egg effectively immobilizes the water so the heat conduction is purely conduction (no convection). Plot the temperature of the egg over time and use the data tooltip in MATLAB to make your conclusion on the time it takes to cook the egg in minutes.
3.4 Estimate the rate of heat loss due to radiation from a covered pot of water at 95 ° C. How does this compare with the 60 W that is lost due only to convection and conduction losses? What amount of energy input would be needed to maintain the water at its boiling point for 30 minutes? The polished stainless steel pot is cylindrical, 20 cm in diameter and 14 cm high, with a tight-fitting flat cover. The air temperature in the kitchen is about 25 ° C. State any assumptions you make in deriving your estimates
None
Hot water is transferred through a stainless steel pipe of 0.06m inside diameter and 5m length. The inside wall temperature is 100OC, the outside surface temperature is 80OC, the thermal conductivity of stainless steel is 16 W/mOC, and the wall thickness is 10 mm. Calculate the heat losses if the system is at steady state.
A plaster wall which is 20 cm thick with a thermal conductivity of 0.3W/m2 C is used in a certain house. The inner wall temperature is at 40C, and the outer wall is exposed to ambient wind and the surroundings at 12C. The film coefficient, h, for convective heat transfer in a 10m/s wind is about 21W/m2C. Ignoring any radiation losses, find the overall coefficient for the conduction and convection losses in W/m2 C О а. 1 O b. 10.1 О с. 1.4 O d. 8.1
Q5Two large containers A and B of the same size are filled with different fluids. The fluids in containers A and B are maintainedat 0° C and 100° C, respectively. A small metal bar, whose initial temperature is 100° C, is lowered into container A. After1 minute the temperature of the bar is 90° C. After 2 minutes the bar is removed and instantly transferred to the othercontainer. After 1 minute in container B, the temperature of the bar rises 10°. How long, measured from the start of theentire process, will it take the bar to reach 99.9° C?
Q1: (5pt) In a cylindrical fuel element for a gas-cooled nuclear reactor, the generation rate of thermal energy within the fuel element due to fission can be approximated by the relation q(1) W/m³ %3D where a is the radius of the fuel element and is constant.The boundary surface at r = a is maintained at a uniform temperature Tɔ. (a) Assuming one-dimensional, steady-state heat flow, develop a relation for the temperature drop from the centreline to the surface of the fuel element. (b) For a radius of a = 30 mm, the thermal conductivity k = 10 W/(m °C) and qo = 2 x 107 W/m³, calculate the temperature drop from the centreline to the surface. 02: (5pt)
you are asked to design a heating system for a swimming pool that is 2m deep 25 m long and 25 m wide. your client desires that the heating system to be large enough to raise the water temperature from 20 to 30° C in 3h.the rate of heat loss from the water to the air at the outdoor design conditions is determined to be 960W/m^2 and the heater must also be able to maintain the pool at 30° C at those conditions.heat loses to the ground are expected to be small and can be disregarded.the heater considered is a natural gas furnace whose efficiency is 80 percent. what heater size (in kW input) would you recommend to your client?
Q6- A 1.0-kW heater is constructed of a glass plate with an electrically conducting film that produces a constant heat flux. The plate is 60 cm by 60 cm and placed in an airstream at 27°C, 1 atm with uxo = 5 m/s. Calculate the average temperature difference along the plate
A mass of 300kg of oil is cooled in 1 hour from 70 celcius to 35 celcius in a cooler consisting of a bank of tubes through which hot oil passes. Cooling water circulates around the outside of the tubes. Calculate the mass of cooling water required per hour if the water temp increases by 21 degrees celcius . Specific Heat of Oil - 2.0 kJ/kg deg C Specific Heat of Water - 4.186 kJ/kg deg C