A 0.550 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 7.5 in., and the load applied to each pulley is P = 58 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. A B, D L L /3 /3 /3

A 0.550 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 7.5 in., and the load applied to each pulley is P = 58 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. A B, D L L /3 /3 /3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 600mm diameter steel shaft is subjected to the torques shown. Determine torsion at each section. Assume G = 75 GPa. P=74 1.5P= 1.5(74) = 111 kNm 3P= 3(74)= 222kNm
1. "ll zain IQ Qz 5 torsion.p.. Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free at end B. If it is subjected to the couple, determine the maximum shear stress in regions AC and CB of the shaft. G = 75 GPa. 3 kN 3 kN 400 mm 50 mm 50 mm 600 mm
If the allowable bearing stress for the material under the supports at A and B is Ob = 780 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= i W a B b lb P
answer only letters D and E
1. Answer Set A only
Detailed Solution please
i need the answer quickly
A wooden frame shown below is supported by a tie rod CF and a pin support at A. The diameter of the tie rod CF is 30 mm, and the cross-sectional area of member BD is 900 mm?. The diameters of the pins at A and D are 8 mm and 12 mm, respectively, and each pin is subjected to double shear. If the weight of the bucket hanging from end E is 3 kN, determine (a) The axial stresses in tie rod CF and member BD. (b) The shear stresses in pins A and D. - 0.6 m-0.6 m→ D E 0.6 m V30B 1.2 m F
3. The center post B of the assembly has an original length of 124.8 mm whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross sectional area of 400 mm². Ea=70 GPa. Use the Force Method 100 mm -100 mm 800 kN/m 125 mm 800 kN/m
Ql:- The system of gears B and C take out power 150 and 175 hp respectively from a motor A that has 325hp, Find the shaft dimeter if the allowable shear stress is 6250 psi and the angle of twist between gear C and motor is 2 degree. Let G=11.5 x 10° psi. Gear Gear Motor A B
Need correct and well-explained solution. Please solve it correctly. Thank you.
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. A 4 in. 3.5 in. 3.5 in. ID В C te-4 ft- | 2 ft - 6 ft-