9.42 Find. Iy for the region shown. 40 Dimensions in mm 160 40 L. F160– Fig. P9-42 Answer: -61.4 x 106 mm4

Q: Both portions of the rod ABC are made of an aluminum for which E= 70 GPa. Knowing that the magnitude…

A: Given : E = 70 GPa This is a problem of solid mechanics where we are asked to determine : a) The…

Q: Can we use czmesh command with contact element to modeling debonding?

A: When czmesh command is used with elements with more than one stiffness no. then it shows an error.

Q: Please recheck Ra and Rb is actually equal to 6kn and not 15kn

A: As per the given question, we have to check the reactions at supports. Original question was: A beam…

Q: At a point in a stressed body, the known stresses are o, = 37 MPa (T), oy = 24 MPa (C), o, = 20 MPa…

A:

Q: Determine the centroid for the sections shown. 20cm Scm 15cm 5cm Scm 30 cm Fig 1

A:

Q: 6,2 and cœntroid of the following Afanes Cross-sectons 2"

A:

Q: The beam cross sections shown are symmetric about the x and y axes. Determine the area moments of…

A: Given data,beam cross section is given top flange width =140mmheight=250 mmthickness of web =6…

Q: 1 = l2 The radius is (mm) 100mm

A: Given:- Ix1=Ix2 To find:- radius

Q: The thin rectangular plate shown is uniformly deformed such that ɛx = +864 µɛ, ɛy = -510 µɛ, and yy…

A: This is the problem involving strain transformation. The angle made by BD with horizontal is to be…

Q: Determine the centroid C of homogenous strips

A:

Q: 5 Find the centroid of the following structure. (20 2.5" dia hole- centered 4" 5" 3" 4" 6" 3"

A:

Q: 9.22 Compute I, for the region shown. 18 2 2 Dimensions in inches Fig. P9.22

A: if you have any doubt please comment

Q: 5 m 4 m 6 m

A:

Q: Use Virtual Work Method to answer the questions below considering the truss shown. Use the…

A:

Q: 7 in. 9.9 in. 14 in. 7 in. 14 in. 16 in.

A: Given:- the wire shown, composed of 4 sections.

Q: Steel railroad rails 10 m long are laid with end-to-end clearance of 5 mm at a temperature of 18°C.…

A:

Q: The thin rectangular plate shown is uniformly deformed such that & = +874 pɛ, ɛ, = -536 uE, and yy…

A:

Q: Locate the centroid of the plane area shown.

A: Given: r1=72 mmr2=120 mm To find: Centroid of plane area.

Q: ๆ 100 mm -100 mm- H 100 mm- 150 mm ·X

A:

Q: 9-79 Determine , , and area. for the rectangle where C is the centroid of the 120 mm Fig. P9.79 80…

A: Determine the moment of inertia with respect to the x axis.

Q: 50KN A 20 KN K-5m----5m-- QUESTION: FIND DEFLECTION AT MIDSPAN. B

A: The given beam is a simply supported beam and is statically determinate beam. The deflection at the…

Q: -30- 30 15 Dimensions in mm Fig. P9.23 x 9.23 For the plane region with a circular cutout, (a) find…

A: I hope this is helpful.

Q: 6. Locate the centroid of the plane area shown below. 50 cm 30 cm 20 cm

A:

Q: 5- What should be the maximum value of cant excess on Broad gauge? a. 65mm b. 75mm c. 92mm d. 100mm…

A:

Q: 9.89 Determine I, and Iy for the region shown. 90 mm 60 mm 90 mm Fig. P9.89

A: Sketch the shaded region as shown in Figure 1.

Q: Example: Determine the forces in each member of the truss shown in the figure and indicate whether…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: 9.24 Determine I, for the triangular region shown. y 4 in. 4 in. Fig. P9.24 3 in. 2 in. x

A:

Q: 535 250 !! A23. The area of the shaded section shown in Fig. P-A23 is 40 X 103 mm?. If I,, X 10°…

A: Find moment of inertia about X2 axis?

Q: Determine the forces exerted at C and E on the tong BCE.

A:

Q: 3. Determine the centroid of the lamina shown in Figure -100 mm- -20 mm 25 mm 70 mm

A: To find out the centroid of the lamina?

Q: The kinematic indeterminacy of the frame shown is? Hinge ATT C

A: Given- Frame as shown- It is needed to find the kinematic indeterminacy Dk.

Q: Find atran changein Inihal lenyth lanyth=D3mm 255mm %3D %3D

A: Given data : Initial length (L)=255 mmChange in length (∆L)=3 mm

Q: Q2: Determine the centroid of shaded arca shown in Figure. Take b-10 cm.

A: Given: The value of b is 10 cm. Consider the figure,

Q: IHEXAGON tencile =

A: Given:- P=15000N hexagon side=1.5cm To find:- tensile stress

Q: 14" 10' 2" 2" 14" (3) Sx = ? (4) Zx = ?

A:

Q: 9.21 Compute I, for the region shown, given that x=25.86 mm. 60- 30 25 90 20 Dimensions in mm Fig.…

A: Approach to solving the question:To compute the moment of inertia Iy​ for the given region about the…

Q: Determine the resultant of the four forces and one couple which act on the plate shown. 2 m 5 m 60 N…

A: Given:- Four forces and a couple are acting on the plate The magnitude of the forces are = 60 N, 50…

Q: The thin square plate shown is uniformly deformed such that , +1.360 ut. , -628 ut, and y=+1.285…

A:

Q: 300 mm 20 mm -20 mm 300mm

A:

Q: Solve dy _х-2y ; у (1) %3 -1 %D dx

A: