9.3-20 Derive the equations of the deflection curve for a cantilever beam AB carrying a uniform load of intensity q over part of the span (see figure). Also, determine the deflection 8 at the end of the beam. Use the second-order differential equation of the deflection curve. A В PROBLEM 9.3-20

9.3-20 Derive the equations of the deflection curve for a cantilever beam AB carrying a uniform load of intensity q over part of the span (see figure). Also, determine the deflection 8 at the end of the beam. Use the second-order differential equation of the deflection curve. A В PROBLEM 9.3-20

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Problem C-3 [Beam Bending - Normal Stress] A simply supported beam (i.e., with a pin support at…

Q: Determine the fixed-end moments (MA andMB) and fixed-end forces (RA and RB) for a beam oflength L…

A: given; lets take reaction force at A=RAlets take reaction force at B=RBweight density=q0AB=LAC=CB=L2…

Q: A beam ABCDE has simple supports at B and D and symmetrical overhangs at each end (see figure). The…

Q: BP4: A simply supported beam of constant El and length L is supporting a distributed load omega w…

A: The given beam is as shown below, To determine deflection at C by Castilagino's method we will…

Q: Figure 4 shows a simply supported timber beam AB with 4.5 m long carrying the uniformly distributed…

Q: A cantilever beam has a length L =12 ft anda rectangular cross section (b = 16 in., h = 24 in.).…

A: Calculate the moment of inertia of the beam. I=bh312 Here, I is the moment of inertia of the beam, b…

Q: A beam ABCDE has simple supports at B and D and symmetrical overhangs at each end (see figure). The…

A: Given that ,

Q: The Flexor loading micrometer will be used to load the beam. Calculate the deflection equired to…

A: On substituting the given values of 'L', 'E' in the given equation of deflection we get y…

Q: A beam is a structural member that is subjected primarily to transverse loads. The beam AB in Figure…

Q: A simply supported beam hinged at A and supported at C, is carrying a distributed load and a point…

Q: A flywheel weighted 1000 N is attached in the middle of the shaft and tensions of 300 N and 600 N…

Q: In the figure, aluminum [E = 78 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

Q: A simple beam AB of length L supports aconcentrated load P at the midpoint (see gure).(a) Evaluate…

A: Given data as per question The load applied =P Calculations ∑Fx=0HA=0∑Fy=0RA+RB=P…

Q: Derive the equation of the deflection curvefor a cantilever beam AB when a couple M0…

A: Given data as per question The moment applied at point B =M0 Length of cantilever =L Calculations…

Q: The frame shown in the figure consists of abeam ACB supported by a strut CD. The beam haslength 2L…

A: Given data as per question Length of beam =2L Calculations considering Part AC,the moment is given…

Q: A cantilevered bar in the figure is acted up on by a system of forces Fx 75 lb, Fy = 200 lb, and Fz…

A: according to the given details

Q: A 3-meter-long beam is used to support a heavy object. The object has a uniform distributed load of…

A: Given:To find:(a) Label the element and node numbers (either on the figure or with a new simple…

Q: QUESTION 4 Solve the problem by the moment-area method. The beam has constant flexural rigidity EI.…

A: To find : The deflection δAand δB at point B and C . Given : The moment of inertia is I=18.1×106…

Q: The diver has a mass of 75 kg and is standing motionless at the end of a diving board shown in…

A: Given data, Mass of the driver, m = 75 kg So, weight of the driver is W=mgW=75×9.81W=735.75 N Young…

Q: The simply supported beam carries a uniformly distributed load over parts of its length. Compute (a)…

Q: A curved frame ABC is fixed at one end and subjected to a concentrated load P, as shown in Figure.…

A: →For section AB(0≤x≤L):-Mx=PxMx=0=MA=0Mx=L=MB=PL →For section BC:- Equation of moment at an angle…

Q: are with uniformly distributed lc

A: given:

Q: 9.3-2 A l-meter-long, simply supported copper beam (E = 117 GPa) carries uniformly distributed load…

A: given data; young modulus(E)=117GPa =117*103MPalength of beam(L)=1m…

Q: Beam ABC is loaded by a uniform load q andpoint load P at joint C. Using the method of…

A: Given data as per question L = 4 m, a = 2 m , q = 15 kN/m, P = 7.5 kN,E = 200 GPa, I = 70.8 X106…

Q: Consider the beam shown in sketch below, hinge supported at point A and roller supported at point D.…

A: Considering the cross-section of the beam The web is denoted as 1 and flange is denoted as 2

Q: (a) Calculate the required section modulus S if Oallow = 18,000 psi, L = 32 ft, P = 2900 lb, and q =…

Q: In the figure, aluminum [E = 79 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

A: Find the deflection at point B.

Q: 10.4-29 A propped cantilever beam is loaded by a triangular distributed load from A to C (see…

Q: A cantilever beam AB is acted upon by auniformly distributed moment (bending moment, nottorque) of…

A: The shear force at any section of a cantilever beam is equal to the total of the loads between the…

Q: An overhanging beam ABC with flexuralrigidity EI=15 kip-in2 is supported by a sliding supportat A…

A: Given Length, L = 30 in b = 15 in EI=15 kip-in2 Find Stiffness of…

Q: A beam with a uniform load has a sliding support at one end and spring support at the other. The…

A: Given Data The stiffness of the spring is: k=48EI/L3 The reaction force acting at B is: RB=kδB The…

Q: A cantilever beam AB of length Land uniform flexural rigidity El has a bracket AC attached to its…

Q: Problem 2: The cantilever beam shown below consists of two structural steel channels, size 3 in x 5…

A: Draw the FBD for the given question. Now write the given values along with suitable variables and…

Q: he beam is subjected to a point load and a distribution load as shown in Figure 2-1 below, and the…

Q: 11-1 A fixed-end beam AB of length L supports a uniform load of intensity q (see figure). Using the…

A: Here we will use fourth order derivative of deflection curve to get the support reactions.

Q: 9.3-12Derive the equation of the deflection curve for a cantilever beam AB supporting a load P at…

Q: 9.4-7 A beam on simple supports is subjected to a parabolically distributed load of intensity q(x) =…

Q: A) Calculate the deflection and rotation at point (c) for the beam showing in figure by using unit…

Q: Derive the equation of the deflection curvefor a cantilever beam AB supporting a load P at thefree…

A: Given Load = P Length = L Find Deflections

Q: A cantilever beam AB of a length L has a fixed support at A and a rollersupport at B(see figure).…

A: The expression for the fourth-order differential equation of the deflection curve. Elv""=-q=0....(1)…

Q: Modulus E of elasticity, for the ACB beam with inertia I; a- Find the elastic curve equation with…

A: In the question we are required to write the equation for the elastic curve and then find reaction…

Q: 5.8-6) A cantilever beam of length L = 2 m sup- ports a load P = 8.0 kN (see figure). The beam is…

Q: A B Fuztuzt -L/2- -L/2- L/2 - Find deflection in the middle part of the EU on the beam in the…

A: Let us consider a dummy load P at the mid of beam i.e 3L/4 distance from both the ends. The free…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

9.3-20 Derive the equations of the deflection curve
for a cantilever beam AB carrying a uniform load of
intensity q over part of the span (see figure). Also,
determine the deflection 8, at the end of the beam.
Use the second-order differential equation of the
deflection curve.
A
PROBLEM 9.3-20

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A propped cantilever steel beam is constructedfrom a W12 x 35 section. The beam isloaded by its self-weight with intensity q. The lengthof the beam is 11.5 ft. Let E = 30,000 ksi.(a) Calculate the reactions at joints A and B.(b) Find the location of zero moment within span AB.(c) Calculate the maximum deflection of the beamand the rotation at joint B.
Obtain the equation of the deflection curve for the simple supported beam AB (see figure). Also, determine the angle of rotation at the right hand support and the deflection at point D P= 120 kN q 20 kN/m A В 10 m 5 m 5 m L R
A cantilever beam AB supports a distributed load of peak intensity g, acting over one-half of the length (see figure). (The beam has constant flexural rigidity EI. Use the second-order differential equation of the deflection curve. Enter the magnitudes.) ly 90 A C В L/2- L/2 Derive the equations of the deflection curve for the beam. (Use the following as necessary: qo, L, E, I, x.) Osxs v(x) = sxsL vx) = Also, obtain formulas for the deflections 8, and 8. at points B and C, respectively. (Use the following as necessary: 9,, L, E, I.) 7 160 E·I 11 %0 L3 192 E·I
A cantilever beam carries a trapezoidal distributed load ( see figure) . Let wB=2.5 kN/ m, wA= 5.0kN/m, and L = 2.5 m. The beam has a modules E = 300 mm, Use the method of superposition and cases 1 and 8 in Table H-1 to calculate the deflection and rotation at B.
A cantilever beam has a length L =12 ft and a rectangular cross section (b= 16 in., h=24 in.), A linearly varying distributed load with peak intensity qoacts on the beam, (a) Find peak intensity q,if the deflection at joint Bis known to be 0.18 in. Assume that modulus E= 30,000 ksi. (b) Find the location and magnitude of the maximum rotation of the beam. TITT В h PROBLEM 9.3-15
. The cantilever beam shown below has a length L, moment of inertia I, and is made from a material with modulus of elasticity E. The load P is applied at the end of the beam. a. Derive the maximum deflection of the beam and show that max Ely" (x) P PL³ ЗЕІ' b. Consider E = 29 x 10³ ksi, P = 6 kip, I = 204 in 4, and L = 15 ft with the length and moment of inertia measured with ±5% and ±10% accuracy, respectively. In 3 significant figures, calculate the deflection and express the variation of its worst-case error. 8max Hint: M(y) =
h F The beam of length 5.9 (m) and cross section base 0.10 (m) and height 0.16 (m) shown is made of plain steel with a modulus of elasticity of 200 (Gpa) and an ultimate strength of 400 (Mpa). The load is 250 (N) and the point q is 4.0 (m) from the wall in the x direction. What is the magnitude of vertical deflection of the beam at point q in units of meters?
A right-angle-cantilevered bracket with concentrated load and torsional loading at the free end is shown in Figure. Using Castigliano’s Theorem, find the deflection at the free end in the z-direction. Neglect transverse shear effects.
A cantilever beam ACB supports two concentratedloads P1 and P2, as shown in the figure. Determinethe deflections δC and δB at points C and B,respectively. (Obtain the solution by using the modifiedform of Castigliano’s theorem.)
Using superposition, find the deflection of the steel shaft at A in the figure. Find the deflection at midspan. By what percentage do these two values differ? Take the magnitude of force (F) to be 355 lbf, w = 130 lbf/ft, and a = 13 in. 0 a F Z₁₁4 1.5 in-dia. shaft 24 in W X The magnitude of the deflection of the steel shaft at A is The magnitude of the deflection at midspan is -0.0475 The percentage difference is 35.28 %. 0.0734 inch in the downward direction. inch in the upward direction.
1 B) Calculate the deflection and rotation at point (a) for the beam showing in figure by using unit load method. (E = 200*10° kN/m2, I = 3.125*10³ m*). 30 kN 6 KN/m a 2 2m 3m
The cantilever is subjected to a point force "P" in the middle of the beam span. The beam's modulus of elasticity, E-200 GPa and moment of inertia, l= 6x10^6 mm^4, are the same at every point. Accordingly, in which option is the maximum deflection (vertical displacement) in the beam given in "mm"? P= 12 kN, L= 2.8 m.