9. What is the default hold-down timer on R1: c. 360 Sec а. 18 Sec b. 240 Sec d. 180 Sec e.90 Sec 10. The cost from R1 to the 3.3.3.0/24 network is: a. 2 b. 1 с. 3 d. 4 e.0 11. What type of Routing updates are sent through RIP Protocol: a. No Updates b. Triggered c. Partial d. Full Routing Table e. static

9. What is the default hold-down timer on R1: c. 360 Sec а. 18 Sec b. 240 Sec d. 180 Sec e.90 Sec 10. The cost from R1 to the 3.3.3.0/24 network is: a. 2 b. 1 с. 3 d. 4 e.0 11. What type of Routing updates are sent through RIP Protocol: a. No Updates b. Triggered c. Partial d. Full Routing Table e. static

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Question 1. a. At transport layer UDP uses checksum to detect errors in the received data. Suppose areceiver received 1 1 1 0 1 0 1 1 0 0 1 0 0 1 1 0 and 1 1 0 0 1 1 1 0 1 0 1 0 1 0 1 0 1 as UDP data.What will be the checksum value, please calculate?b. What is ICMP and its functionality? Give two example protocols of application layer thatuses ICMP protocol.
Suggest the most appropriate routing methods to be implemented for a small network topology shown below to forward packets from R1 to ISP and vice versa. Justify your answers. 192.168.10.0/24 209.100.10.8/30 GO/0 so/0/1 ISP Internet R1 so/0/0 GO/1 192.168.11.0/24 PC B
A. In RIP protocol: A routing table has 10 entries. It does not receive information about 3 routes for 200 seconds. a. How many timers are running at this time? b. Also calculate the timers running in the above scenario. B. Differentiate between distance vector, Link state vector and path vector routing with example.
Correct and detailed answer will be Upvoted else downvoted
Are you able to clarify the primary differences that exist between stealing a TCP connection and stealing a UPD session?
To get around the problem of sequence numbers wrapping around while old packets still exist, one could use 64-bit sequence numbers. However, theoretically, an optical fiber can run at 75 Tbps. What maximum packet lifetime is required to make sure that future 75 Tbps networks do not have wraparound problems even with 64-bit sequence numbers? Assume that each byte has its own sequence number. as TCP does.
Q8: what is hexadecimal values for the source and destination address in the Ethernet frame containing the ARP request message? *In the filter field of the Wireshark window type arp, and click enter.From the packet list window, select the first ARP request packet.From the packet detail pane, select the Address Resolution Protocol.
What static routes need to be added to routers A and B for PC communication across the whole topology?
A network administrator is determining untagged, port logic for a frame addressed to a port in the same vlan on the same switch, what would happen? A. Forwarded to trunk. B. No tag is Added C. Tag is stripped D. The packet is dropped
A designated router is elected on any ethernet subnet where EIGRP is used. O True O False
Discuss four Routing methods, or algorithms, chosen to move packets through a network.
Questions: 1. From page 41 of the slides, in the data link layer, does the MAC frame change in the transmission? 2. If your answers of question 4 and 5 are not correct, please answer them again. 3. In the IP datagram we use the IP address, and in the MAC frame we use the hardware address. In the slide 40, which source IP address and destination IP address are used in the IP datagram flows on the network layer from H1 to H2?