9. Show that In an a.c. olrcult maximum power is transferred to a load whose Impedance is equal to the conjugate of the Thevenin's Impedance of the circult as seen across the load terminals. If the load consists of only a resistance and no reactance what should be the magnitude of the resistance for maximum power to be transferred to It? Determine.

9. Show that In an a.c. olrcult maximum power is transferred to a load whose Impedance is equal to the conjugate of the Thevenin's Impedance of the circult as seen across the load terminals. If the load consists of only a resistance and no reactance what should be the magnitude of the resistance for maximum power to be transferred to It? Determine.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Leading power factor implies that current leads voltage-a capacitive load Select one: True False CLEAR MY CHOICE
AC Circuits Current, Voltage, Power, Power Factor and Phasor Diagrams. Consider the circuit shown in Figure 3. (i) Find the total impedance ZT as seen by the voltage source. (ii) Find the total current IT supplied by the source. (iii) Sketch phasor diagram of Vs and IT and State whether IT leads or lags Vs (iv) Determine the power factor angle for the circuit. 9. L R1 1002 0.213H IT Vs R3 1502 C 12020°V 22µF 60HZ R2 50Ω Figure 3 Answers |(1) Zr = (ii) IT= (iii)
-The Vollage V= 100210°V is 62 pplied across a capacilive 1oad . The 1-a kes ap paraal' Power Load of 500VA teading Power fracl-or. The reaclance (xc) of load 's---- 7
Lance Smile operated two loads in parallel. The loads draw a total of 3kW at a 90% power factor lagging operating at a 230 Vrms 60-hz voltage source. Load 1 is taking 1000 W at 80% power factor lagging. Determine the following: a. The power factor of the second load. b. If a capacitor is connected in parallel with the loads, what is the value of the capacitance needed to correct the power factor to 95% lagging for the combined load.
3- Please I want answer of this Electrical Principles question. Thanks
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
3. A 12020⁰ Vrms is to supply power to a welder, heater and an induction motor. A welder is a coil of (4+j3) ohm, the induction motor draws 60KW with 0.8 power factor, and the heater is a resistor that draws 15KW power. Find the complex power, real power, reactive power and the total power factor that must be supplied by source. If a capacitor will be used to supply a reactive power in the circuit in order that the net load will have a unity power factor, what reactive power must be supplied by the capacitor? Draw the circuit.
To attain maximum power delivered to a load, what value of load impedance is required if a. the load can have any complex value; b. the load must be pure resistance?
2)With reference to the waveform given below formulate the equation for the average value of DC voltage available across the load, if the load connected is a pure resistive load and if the circuit applicable tot his waveform is fed from a load having 180 volt 50 Hz start connected input with the value of resistance equivalent to 200 ohm solve and obtain the value of Dc power in the load (3 phase bridge) Van Vbn Vcn +Vm P 180° 210° 360° D3&D4 D5&D4 D5&D2 D1 & D2 D1&D6 D3 & D6 120° 120°
Three impedance Za= (3+j4) ohms, Zc= (4-j4) ohms and Zr=0+j3 ohms are connected in parallel. Solve for the pf of the combination.
Solve for the following problems. Round off your answers to 2 decimal places. Show your complete solution. Write legibly.
An inductive impedance and a resistance is connected in series with a 220V ac source. The power factor of the circuit is 0.94. If the voltage drop in the impedance is the same as the voltage drop across the resistance, find the voltage across the impedance.