Answered: 9. If P = 150 kN, determine the elastic…

9. If P = 150 kN, determine the elastic elongation of rod BC and the decrease in its diameter. Rod BC is made of A-36 steel and has a diameter of 40 mm. (E = 200 GPa, v= 0.32)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A solid plastic rod has a diameter of d = 30 mm and a length of L = 625 mm. An axial load of P = 21…

A: Given: Diameter, d = 30 mm Length, L = 625 mm Axial load, P = 21 kN Elastic modulus, E = 2.4 GPa…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

Q: he rigid bar AB with a length of 5m, is attached to two vertical rods and is horizontal before the…

A: Given

Q: A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P…

Q: Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P…

Q: Two members AB and AC are made of material with E= 91 Gpa and each member has cross sectional area…

A: Given: E=91 GPaP=2079 NL1=202 mm =0.202 mL2=313 mm=0.313 mL3=480 mm=0.48 m

Q: Question 53 What is the elongation of the aluminum bar with a dimension of 25 mm by 25 mm and length…

Q: 10.14. If P = 1000 Kg find the diameter of the elements subjected to compression to avoid buckling.…

Q: The rigid beam supports the load of 50 kN as in the figure below. Determine the displacement at B.…

A: As per given question The rigid beam supports the load of 50 kN as in the figure below. Determine…

Q: If block A is intended to move vertically at a constant rate of 5.61m/s by pulling cord at point B,…

Q: The truss shown in the figure below is made from A992 steel rods having a diameter of 30 mm and…

Q: В D 6 kN 5 kN 4 kN A - 2 m→2 m→ -3 m- -3 m

Q: Determine the Euler Buckling axial compressive load of W 12 x 72 section having a length of L=48 ft…

A: To find: The Euler Buckling load. Given: The length of the column, L = 14.63 m. Young's modulus, E =…

Q: Calculate the elastic elongations that will occur in the x y axis on the adjacent object according…

A: given stress in x direction σx=-30 MPa (compression)stress in y direction σy=40Mpa (tensile)young…

Q: Based on the allowable stress for the bronze, calculate the maximum allowable force that can be…

Q: The stick in the left picture is from the right end welded and the material from which it is made…

Q: A 3.5-m long column with rectangular cross section of 4 cm x 3 cm is under an axial compressive load…

Q: Determine the maximum deflection of the simply supported beam. Express your answer to three…

A: The maximum deflection. Given: The modulus of elasticity is E=150 GPa=150×109 GPa. The moment of…

Q: The push rods on the suspension of the Pitt Formula SAE race car are Chome-moly steel (E = 29,000…

A: The elastic modulus is .The yield stress is .The length of rod is .The outside diameter is .The wall…

Q: Compute the total elongation caused by an axial load of 147 kN applied to a square bar, tapering…

Q: For the structure below, calculate the diameter of the pin G, considering that its allowable stress…

Q: A bar of varying square sections is loaded as shown in the figure. Determine the total elongation.…

Q: The length of the rectangular arm, which is fixed at both ends, is L= 9 m, and the cross section is…

Q: The cylindrical bar composed of two parts (AB and BC) is fixed at ends A and C. The two parts are…

Q: At temperature of 25oC, a 17 m rod 8 mm in diameter is subjected to a tensile load of 24 kN. At what…

Q: Two members AB and AC are made of material with E= 138 Gpa and each member has cross sectional area…

Q: An aluminum alloy tube with an outside diameter of 3.1 in. and a wall thickness of 0.36 in. is used…

Q: A solid plastic rod has a diameter of d = 33 mm and a length of L = 575 mm. An axial load of P = 32…

Q: A rectangular column is made of a grade of sawn wood that has an adjusted allowable stress for…

A: Write the given data. σC=8.3 MPaE=11.1 GPaP=105 kNe=0.025 mb=0.180 md=0.240 m

Q: A solid plastic rod has a diameter of d = 38 mm and a length of L = 700 mm. An axial load of P = 21…

Q: Determine the horizontal displacement of end point D of the steel rod shown in the figure. E=200 GPa…

Q: A 5 m long tension member (E=70GPA) has a cross sectional dimensions of 25mm x 50mm. if an axial…

A: Given data:

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P =…

Q: A solid plastic rod has a diameter of d = 44 mm and a length of L = 700 mm. An axial load of P = 22…

Q: A column with rectangular cross section of breadth = 9mm and depth = 4mm, has its both ends are…

Q: If the temperature of the 85 mmmm diameter post CD is increased by 60 ⚫C, determine the force…

Q: Problem 4. The structure in the figure is composed of two rigid bars (AB and CD) and two vertical…

A: The free-body diagram of the beam is as shown below, Assumption: Let the length of aluminum and…

Q: The rod BD is made of materia with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at…

A: The above question is based on Torsion of shafts.

Q: of d₂ = 0.75in. Aluminum e aluminum is 40 ksi. Assu fely be applied to the stru

A: BronzeE1=15000ksid1=0.60inYield-strength=48ksiAluminiumE2=10000ksid2=0.75ind3=1.00inYield-strength=4…

Q: The cross-sectional area of the bar is 5 cm². Use E = 70 GPa for aluminum, and E = 200 GPa for…

Q: A steel rod having a cross-sectional area of 300 mm2 and a length of 150 m is suspended vertically…

Q: The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

9. If P = 150 kN, determine the elastic elongation of rod BC and the decrease in its
diameter. Rod BC is made of A-36 steel and has a diameter of 40 mm.
(E = 200 GPa, v= 0.32)
-1 m
-1 n
1 m
0.75 m
[Ans: OBc = 0.933 mm, &a= -9.55(10³) mm]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need help on solving this question
Please solve quesition no 207.
A steel rod having a cross – sectional area of 300 mm2 and length of 15 m is suspended vertically from one end. It supports the load of 30 kN at the lower end. If the unit mass of steel is 7850 kg 3 m and Young modulus of Y = 200 GPa, find the elongation of the rod.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Determine the elongation or reduction of each member if the magnitude of force P is 9 kN. Also, what is the total elongation or reduction of all members? Indicate reduction by adding the minus (-) sign in your final answer. Bronze Aluminum Steel A=400 mm? P A=600 mm? A= 300 mm? 4P 4P P 3 m 5m 4 m- 2.
The 24-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Figure 600 mm B 400 mm 50 kN 50 kN C 40 kN 1 of 1 > ▾ Part A Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. dc = Submit μA Value Provide Feedback Request Answer Units ? 4
Introduction to Fem
QI\ Determine the elongation of the system shown in figure below 100 kN 50 kN 50 kN steel Copper E=117GPA Bronze E=210GPA E=82GPA A=1500mm A=1000mm A=500mm
Mechanic Of Materials
Rigid bar ABC is supported by two aluminum alloy (E = 10,000 ksi) rods as shown below. The horizontal distance between rods (1) and (2) is a = 150 in. Rod (1) has a length of L₁ = 99 in. and a cross-sectional area of A₁ = 0.55 in.². Rod (2) has a length of L₂ = 96 in. and a cross-sectional area of A₂ = 0.95 in.². Rigid bar ABC is to remain horizontal under a load of P = 35 kips. Determine the distance x from joint A to the location of load P so that bar ABC remains horizontal. L Answer: X= i (1) eTextbook and Media Save for Later x in. B (2) L2 Attempts: 0 of 5 used Submit Answer
8
Part A A FA. FD= -600 mm- P 50 mm VE ΑΣΦ 41 B vec - 600 mm 25 mm If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the support reactions at A and D when the force P = 200 kN is applied. The assembly is made of A36 steel. (Figure 1) Enter your answer, separated by a comma. -0.15 mm D ? kN
Assume portion ABC of the rod is made of steel (E4e= 200 GPa , v=0.3) and portion CD is made of aluminum (E,lumi = 70 GPa , v=0.25). A 1.75 m Area = 800 mm² 120 kN B 1.25 m C Area = 500 mm² 1.5 m 80 kN D 60 kN The deflection of point C is_ The resulting change in diameter of portion AB of the bar is_