9:55 @← Expert Q&AYTE 929. A shunt motor runs at 1200 rpm on a 420 V circuit and current taken in 30 A inaddition to the field current. What resistance must be placed in series witharmature in order that the speed may be reduced to 600 rpm, the current throughthe armature remaining same. Ra = 302 given. (5.52)10.A 220 V DC series motor is running at a speed of 800 rpm and draws 100 A.Calculate at what speed the motor will run when developing half the torque.Armature + field resistance is 0.1 2. Assume that magnetic circuit is unsaturated.(1147 rpm.)11.230 V, DC shunt motor runs at 800 rpm and takes armature current of 50 A. Findthe resistance to be added to the field circuit to increase the speed from 800 rpmto 1000 rpm at an armature current of 80 A. Assume the flux to be proportionalto the field current. Given ra = 0.1502 and rf = 2500.(699.)■

We are authorized to answer one question at a time, since you have not mentioned which question you…

9. A shunt motor runs at 1200 rpm on a 420 V circuit and current taken in 30 A in addition to the field current. What resistance must be placed in series with armature in order that the speed may be reduced to 600 rpm, the current through the armature remaining same. Ra = 302 given. (5.52)

9. A shunt motor runs at 1200 rpm on a 420 V circuit and current taken in 30 A in addition to the field current. What resistance must be placed in series with armature in order that the speed may be reduced to 600 rpm, the current through the armature remaining same. Ra = 302 given. (5.52)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: What are the following statements are true for DC Motor? I. Motor converts Mechanical Energy to…

A: Motor converts electrical energy to mechanical energy. Only I is false remaining true

Q: A 240 V shunt motor has an armature current of 15 A when running at 800 rpm against full-load…

A: In this question we need to find a What resistance must be inserted in series with the armature to…

Q: types of power losses of DC motor

Q: Find the starting current (in Ampere) of 146 V DC series motor if the armature resistance = 0.6 ohm…

A: armature current of DC series motor=(terminal voltage -back emf)armature resistance+ series field…

Q: A series motor runs at 700 rev/min when the voltage is 300 V and the current is 20 A. The armature…

A: Initial speed of motor N1=700 rpm. Initial terminal voltage V1=300 V. Armature current Ia=20 A.…

Q: A 230-volt series motor has an armature resistance of 0.32 ohm and a series-field resistance of 0.16…

A: Given: V=230 VRa=0.32 ΩN=500 rpmIa=32 A

Q: Speed control 11 12 field 1 h eo stat 5 Prime armature E1 Mover 6. DC Generator Power Supply Load…

Q: A d.c. shunt motor is running with certain load. For constant torque, the effect of adding an…

A: As per the guidelines of Bartleby we supposed to answer 1st question only since the 2nd question is…

Q: 2. Assume negligible inductance for the motor model shown in Figure 1. This motor is connected to a…

Q: If the losses of the armature wingdings of dc motor which is running at 1200 RPM is neglected and…

Q: (1) What is the armature current IA for EA= (A-10)V (2) What is new value of EAnew, at C/5 percent…

A: RA=0.25Ω ;VT=A=436 V ;EA1=A-10=426V ;1 IA1=? for EA=A-10 C=7, ∴C/5=7/5=1.4% decrease ∴ϕ2=0.986ϕ1 2…

Q: A 500 V shunt motor running at 720 rpm takes an armature current of 50 A. The equivalent armature…

A: Terminal voltage V = 500 V Initial speed of motor N1=720 rpm Speed after adding resistance, N2=540…

Q: The armature resistance of a DC motor is 0.4 £2, the supply voltage is 200 V and the back e.m.f. is…

A: Given, A DC motor with, Armature resistance, Ra=0.4 Ω. Supply voltage, Vs=200 V. Back emf, Eb=198 V.…

Q: tor has lap-wound arn rotating at 100 slots 2 turms per col. 100rpm. Flux per pole is 100mWb.…

Q: What is the difference between torque of (1- 0) induction motor & torque of (3- 0) induction motor…

A: Given that What is the difference between torque of single phase induction motor & torque of…

Q: Q5- A)- Select the correct answer for the alternatives given 1- Wave windings are used in d.c…

A: As per guidelines given to us we can only provide the solution of first three subpart in multi part…

Q: A DC series motor of resistance 1 ohm across terminals runs at 1000 rpm at 250 V taking a current of…

A: Given, a DC series motor having Resistance across terminal, Rt = 1 ohm Speed, N1 = 1000 rpm Terminal…

Q: Draw torque vs slip for an induction motor.

A: we need to draw torque vs slip for an induction motor.

Q: de motors

Q: across the j16 2 j40 2 ணை j40 2 24 2 100 V/30° ( -jl Q j4 2 =-j82 -j10 2= j10 2 j9 2 10 Ω 32 8 Ω ll…

A: Assume 100[30°] is a RMS Value.

Q: 5. A 20Kw dc shunt generator delivering rated output at 1000rpm has a terminal voltage of 500 V. The…

Q: A 220 V shunt motor has an armature resistance of 0.4 ohm and field resistance of 140 ohm. The motor…

A: We have an shunt motor which is having, Voltage (V) = 220 V Armature resistance (Ra) = 0.4 Ω Field…

Q: Why does the speed change as the load changes in the D.C series motor

A: -The schematic for the loaded DC series motor is shown in the figure below:

Q: QUESTION 3 The direction of the magnetic force on the electron in the figure is A. Out of the screen…

A: Magnetic force given F = q(V×B ) Direction of V is -X Direction of B is +X

Q: 6: The power input to a 415 V, 50 Hz, 6-pole, 3-0 IM running at 975 rpm is 40 kW. The stator losses…

A: Given information is shown below:P= 6f=50 HzPin= 40 WPstator=1 kWPf+w=2 kWNr= 975 rpm

Q: The overall efficiency of a 4-pole DC motor is 83.5% when running at a speed of 550 rpm. The motor…

Q: 4. The field windings of a series motor has a resistance of 120 ohms at 15°C. After running for two…

Q: The current drawn by 220 V dc shunt motor of armature resistance 0.5 ohm and back emf 200 V is

A: Given, A DC shunt motor having Supply voltage, V=220 V Armature resistance, Ra=0.5 Ω Back emf,…

Q: series motor is

Q: 459. The current drawn by a 460 V dc motor of armature resistance 0.5 ohm and back emf 420 V in

A: Given a dc motor with, Input voltage, V = 460 V. Armature resistance, Ra = 0.5 ohm. Back emf, Eb =…

Q: electric car to Permanent Magnet Synchronous Reluctance motor.

A: Tesla made a significant change to its electric motor strategy with the introduction of the Model 3,…

Q: What does 50hp induction motor mean? What does a 10hp load mean

A: In this question we will write about induction motor hp and load hp mean .....

Q: List the four basic faults which can prevent a self excited generator to buildup voltage.

A: We can define fault as imperfection in electrical system due to which current may get deviated from…

Q: ) Describe a single wire DC motor with the help of a diagram.

Q: When the armature current of a 220V DC shunt motor is 40Amper, the armature current of the motor…

Concept explainers

Three Phase Induction Motor

The induction motor is an electric motor that runs on AC (alternating current) and it is of two type single phase motor that work on single-phase power supply and three-phase motor that work on three-phase power supply.

Question

9:55 @
← Expert Q&A
YTE 92
9. A shunt motor runs at 1200 rpm on a 420 V circuit and current taken in 30 A in
addition to the field current. What resistance must be placed in series with
armature in order that the speed may be reduced to 600 rpm, the current through
the armature remaining same. Ra = 302 given. (5.52)
10.A 220 V DC series motor is running at a speed of 800 rpm and draws 100 A.
Calculate at what speed the motor will run when developing half the torque.
Armature + field resistance is 0.1 2. Assume that magnetic circuit is unsaturated.
(1147 rpm.)
11.230 V, DC shunt motor runs at 800 rpm and takes armature current of 50 A. Find
the resistance to be added to the field circuit to increase the speed from 800 rpm
to 1000 rpm at an armature current of 80 A. Assume the flux to be proportional
to the field current. Given ra = 0.1502 and rf = 2500.(699.)
■

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:

VIEW

Step 2: Determination of armature voltage for both cases:

VIEW

Step 3: Determination of series resistance:

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Colve asap
Final 1A DC shunt motor is rated 10HP, 250V and is connected to 235V source. The armature resistance is 0.2 ohm, the field circuit resistance is 125 ohm and the total rotational losses are 380W. The motor is driving a load, and it draws an armature current of 30A, Calculate the output power. b) 41 d) 6490 6870 7492 7460 Boş birak
Do you What is Induction motor?
A 3-0, 6 pole, 50 Hz IM has a rotor speed of 987 rpm. Find rotor frequency? E) 60 Hz. F) 0.65 Hz. G) 0.75 Hz. H) 0.70 Hz.
NEED IN 5 MINS PLEASE URGENT :(( The rotational losses in a dc motor is equal to 400 W. What is the efficiency if the motor output is 1 kW?
A 6-pole, 50-Hz, 3-φ induction motor is running at 950 rpm and has rotor Copper loss of 5 kW. Its rotor input is ......kW. 100 10 95 5.3
Question A dc series motor with a resistance between terminals of 1 0, runs at 800 rpm from a 200 V supply taking 15 A. If the speed is to be reduced to 475 rpm for the same supply voltage and current the additional series resistance to be inserted would be approximately
Find the starting current (in Ampere) of 148 V DC series motor if the armature resistance = 0.6 ohm and the filed resistance = 0.2 ohm %3!
What are the different ways to supply DC power to rotor of an alternator? Which method is superior and why?
1. A 230 V shunt motor takes a total current of 25 A. If the field winding resistance is 100N and the amature resistance of 0.30, Determine the Current in the armature and Back emf I need all steps , write clear please
A DC series motor having a resistance of 0.4 ꭥ and runs at 2000 rpm when connected to 250 V supply and drawing a current of 20 A. (i) What resistance must be added in order to limit the speed to 4000 rpm when armature current is 5A? Assume flux varies linearly. (ii) What resistance must be added to limit the speed to 1000 rpm when armature current is 30 A? Assume that the flux at 30 A is 20% more than that at 20A. (iii) At what speed the motor will run if it is connected directly to 250 V supply when the load is such that the current drawn is 30 A?