9. A long, thin plate of width b, thickness t, and length L is placed between two rigid wallsa distance b apart and is acted on by an axial force P, as shown. Find the deflection ofthe plate parallel to the force P. Also find the component of normal strain in thethin direction.

Step 1: Step 2: Step 3: Step 4:

Answered: 9. A long, thin plate of width b,…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The beam is supported by two wires AB and CD that have a diameter of 12 mm and 8 mm, respectively as shown in Figure Q2. Given the mass of the beam is 500 kg. i. Determine the position d of the 6 kN load so that the average normal stress in each wire is the same ii. Find the strain in wire CD, ɛcD iii. Using d that obtained in Question 2(i), calculate the displacement of point E B Wire AB Steel 6 kN D Wire CD L= 5 m Aluminium E= 200 GPa L=3 m E = 70 GPa E 10 m
Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 4.995 mm. determine the applied force F.
A steel bar of rectangular section 50 mm x 30 mm and length 1.5 m is subjected to a gradually applied load of 150 kN. Find the strain energy stored in the bar. If the elastic limit of the material of the bar is 150 N/mm?, proceed to determine the proof resilience and modulus of resilience.
A thin ring of radius R is subject to internal pressure such that the radius is increased by an amount AR. Find the circumferential strain &. Ans: AR/Ri.
A bar BD is held in a horizontal position when there is no load by the steel wire AB. When a weight Wis added at C, also hanging from a steel wire CE, then point C is displace down by 0.025in. The cross-sectional area of the wires is 0.002in². The wires are made of a steel alloy with E = 29000ksi and oy = 70ksi. Calculate the strain in both wires, and the weight W. 4₁ B A E Parameter ft L_1 4 L_2 1 L_3 2 L_4 4 C The strain in AB is € AB = The strain in CE is ECE = The weight W = W lb cc 080 BY NO SA 2021 Cathy Zupke D in./in. in./in.
A cube of side 40 mm, subjected to 3 mutually perpendicular tensile forces of 9 kN, 5 kN, 5 kN acting along X, Y, Z directions respectively. Find the stresses in each directions and the strain along x direction of the cube. Take Young's Modulus of the material as 210 GPa, Poisson's ratio as 0.3. (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNITS GIVEN IN BRACKET) (i) Stress along X direction (Unit in N/mm2) = 5.625 One possible correct answer is: 5.625 (ii) Stress along Y direction (Unit in N/mm2) = 3.125 One possible correct answer is: 3.125 (iii) Stress along Z direction (Unit in N/mm2) = 3.125 One possible correct answer is: 3.125 (iv) Strain along X direction = 1.785*10^-11
Find the strain in rod if initial length of rod is 190 mm and change in length of rod is 0.0112 mm
A metal wire is 2.5 mm diameter and 2000 mm long. A force of 10 Napplied to it and it extension 0.3 mm. Assume the material is elastic.Determine the:1- Stress, and2- Strain
Based on generalized Hooke's law if a body is subjected to a uniform, hydrostatic pressure p , find the three strain components.
A solid circular rod 200 mm long and 20 mm in diameter has an axial force of P. are exposed. The force P and the extension of the rod when this force is applied ô below the elasticity of the material, taking as the values given opposite your names in the table presented Calculate the modulus E and the shear modulus G. Take the Poisson's ratio (u) 0.3. P (N)= 550 8(mm)= 1,2 P P - 200 mm
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
A rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

9. A long, thin plate of width b, thickness t, and length L is placed between two rigid walls a distance b apart and is acted on by an axial force P, as shown. Find the deflection of the plate parallel to the force P. Also find the component of normal strain in the thin direction.