9. A horizontal cantilever 3m long is of rectangular cross-section 60mm wide throughout its length, the depth varying uniformly from 60mm at the free end to 180mm at the fixed end. A load of 4KN acts at the free end. Find the position of the most highly stressed section, and find the value of the maximum bending stress induced. Neglect the weight of the cantilever itself. 4KN 3m 180mm d mm X 60mm (41.67MPa)

Q: State the depth of improvement ?

A: Soil engineering improves techniques to enhance the soil or ground. Vibro- compaction could be a…

Q: 10. Figure 9 shows a system in which water flows from a tank through a pipe system having a several…

A:

Q: In computer reports, what is a “sort”?

A: In computer reports, sort is defined as an operation which is used for arrangement in an ordered…

Q: Whatis he length of a 2 ine given a scale of 1:40?

A: Given: The measured length of the line is 2”. The scale is 1:40.

Q: Define PDOP?

A: PDOP ( Position dilution of precision) It describes the error caused by the relative position of the…

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: Define Peclet number.

A: It is defined as the ratio of the rate of advection of a physical quantity by the flow to the rate…

Q: Give 2 uses of nails

A: Brief concept- Nails- It is a piece of metal that pointed at one end and flattened at another end.

Q: Define Stripping?

A: Brief concept- It is related to the construction part and also known as De-shuttering.

Q: What are Cole values

A: Solution: COLE stands for The Coefficient of linear Extensibility.  It is used to measures the soil…

Q: Compute total indeterminacy

A: Given data : Number of external support reaction (R)=2+2+2=6 Number of member attach at hinge joint…

Q: what was the unit used in the plan shown above ? autocad

A: There base unit in AutoCad is inch.

Q: missing value

A:

Q: where did you get 6?

A: 6 is the loading intensity at B.

Q: Construct a Project Charter of Construction Project. Be specific and SIMPLE.

A: A construction project charter includes the following details: 1. Overview of the project 2. Project…

Q: Define Lateral Capacity

A: Lateral capacity:

Q: What is Prebid?

A: A prebid is a meeting which generally happens before a bid. It is held to clear up any confusion…

Q: Define Anchorage

A: The constructions made up of steel as a construction material requires connects of nuts and bolts to…

Q: actors that cause hardness along with a bibliography

A: The water hardness may be simply defined as the amount of dissolved calcium and magnesium in the…

Q: What is Landsat and name 2 Civil Engineering Applications can it be used for?

A:

Q: Renolds number, define it?

A:

Q: What exactly is a CompactFlash (CF) card?

A: A Compact Flash card (CF card) is a memory card format that was developed by SanDisk company in the…

Q: According to this figure, What is d? What is dt?

A: Draw the figure.

Q: Slab on grade Define.

A: A slab-on-grade is a type of shallow foundation in which a concrete slab rests directly on the…

Q: 1) Determine the area of the shape below. -130.0- 100.0 -160.0-

A: The above figure is the trapezoid  The area of the trapezoid = sum of the parallel…

Q: What is expert determination?

A: Experts are often assigned by justices and adjudicators in national courts and arbitration…

Q: What is a Subtense bar?

A: Subtense bar:

Q: Compute for the latitude of Line 1-2 A +4.81 B) +5.79 +8.03 D -18.63 Question 11 Compute for the…

A: Data is as given

Q: Find the area of each. Then put in square feet and square yards

A: Explanation(') means foot(") means inches1 square foot = 0.111 square yard1) Area of red rectangle =…

Q: I x,0= 10 " I yo = r x,0 = 4"X6"X ½" r yo = 12" 4"X 8"X 1" | 1" 12 "

A:

Q: Define Alidade.

A: Draw the figure.

Q: What are the two types of waiver's of lien?

A: The waiver of lien is a document from which is signed by a material supplier, subcontractor,…

Q: Define Construction tolerances—The

A: Tolerance in construction:

Q: How many studs are require for the exterior wall on the main floor if there are two doors and 6…

A: Hi! Thank you for the question As per the honor code, We’ll answer the second and third question…

Q: Discuss how volume studies are being conducted

A: Traffic volume studies are conducted to determine the effectiveness of traffic control…

Q: What is the arch dam?

A: Arch dam: It is a curved concrete dam, convex upstream and resists force acting upon it mainly by…

Q: What is Boundary value testing?

A:

Q: diagrams on the spaces provided: For the frame in Figure 1 compute all support reactions and draw…

A:

Q: Beginning ^ 2 3 4 LO 5 CO 9 8 7 3 10 10 11 12. 13 5 14 15 Identify the full name and abbreviation of…

A: To Determine: Full name and abbreviation of 8 10 15

Q: what about CB, IH, AB & AB

A: To find zero force members.

Q: PROBLEM 3 THE BUILDING IN FIG. P1.1 IS USED FOR LIGHT STORAGE SPACE. THE SLAB IS 250 MM. THICK. THE…

A:

Q: 3. £ 65 s² + 25 + 3 s² + 25

A:

Q: Define BIM.

A: Building Information Modeling (BIM) is defined as the 3D model-based process which digitally…

Q: Define Torsion,

A: Torsion: The twisting of a material by the loading of external forces i.e couple which produces…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.