9 mm A' 9 mm 96 mm 60 mm 9 mm

Q: A short column is made by nailing two 1 * 4-in. planks to a 2 * 4-in. timber. Determine the largest…

A: Given Data: The top surface area of center plank (A) is of (2 inchx4 inch) The top surface area of…

Q: Q1 The curved portion of the bar shown has an inner radius of 20 mm. Knowing that the allowable…

A: Given,

Q: The compressed air tank AB has a 250-mm outside diameter and a 10-mm wall thickness. The arm BC is…

A: Stress calculations:

Q: ogeth le of 25° with the horizontal. Knowing that the allowable str 0 kPa and t = 600 kPa, determine…

A:

Q: 2. Link AB, of width b 5 50 mm and thickness t 5 6 mm, is used to support the end of a horizontal…

A: Given:  I think the values given are not correct so i have taken appropriate values to solve this…

Q: A steel pipe of 300-mm outer diameter is fabricated from an 8-mm-thick plate by welding along a…

A: Outer diameter d0= 300 mm Force P = 250 kNThickness =8 mmTorque,T=12 kN.mTo determine:a)The normal…

Q: Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice…

A: Given data: Applied force, P = 11 kN. Resolve the force P into normal and tangential components. F…

Q: Link AB, of width b = 2 in. and thicknesst = ¼ in., is used to support the end of a horizontal beam.…

A: Handwriting.jpg

Q: Link BD consists of a single wooden member 38.2 mm wide and 20.4 mm thick. Knowing that each pin has…

A:

Q: An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall…

A:

Q: 1.3 Two solid cylindrical rods AB and BC are welded together at B and = loaded as shown. Knowing…

A: Given P = 10 kips To find Average normal stress

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: ! Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown.…

A:

Q: (d) the average bearing stress at C in member BC, (e) the average bearing stress at B in member BC.

A:

Q: The rigid bar ABD is connected to the rod BD which consists of a single bar with a width of 25,0 mm…

A:

Q: THE FRAME SHOWN CONSISTS OF FOUR WOODEN MEMBERS, ABC, DEF,BE, AND CF. KNOWING THAT EACH MEMBER HAS A…

A:

Q: A block of 10-in. length and 1.8 3 1.6-in. cross section is to sup-port a centric compressive load…

A: length, L=10-in Sides of the block a=1.8 in,   b=1.6 in normal stress = 18 ksi…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.