9-59. Locate the centroid (x, y) of the composite area. 3 in. 4 in. 3 in. 3 in.

Q: Show the dimensions of the object on its orthographic views.

A: The orthographic views of the object using the third angle projection are as shown along with their…

Q: (Bernoulli/continuity) Water flows steadily through a diverging tube as shown in the figure below.…

A: Given data: d1=0.52 ftd2=0.70 ftd3=0.92 ftSG=2y=2.4 ft

Q: Derive the equation of the elastic curve for the beam using the x coordinate that is valid for 0<x<…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: For the beam shown, do the following: 1. Determine the values of shear at every change of load…

A: Question part 4 and 5 are solved only. As no specific method was asked, so double integration method…

Q: Additional Problem #2 30 mm Locate the centroid of the cross-sectional area at right. Sketch the…

A: The given figure is shown below:

Q: Draw the projections (Top, Front, Side) with Dimensions for this objects

A:

Q: Condition #1: Å structural support for a machine is subjected to a static compression load of 20 kN.…

A: FOR SAE 1040 hot rolled section yield stress is given byσy=415mpawe have σy=PAreaArea=π4d2d=dia

Q: Locate the centroid of the plate area shown below: (All units are in mm). Ø200- Ø150 300 300 Ø50 50…

A:

Q: The rod has a weight of 7.8 lb/ft. It is supported by a ball-and-socket joint at C and a journal…

A: Given data:- The given rod weight is, 7.8 lb/ft

Q: Picture attached

A: The strong acids and strong bases neutralize to form the neutral salts .The neutral slats have the…

Q: please sketch the missing lines and draw the isometric view

A: Answer We can obtain the missing lines and isometric view of given object using the following steps…

Q: the beam shown in the figure, draw the influence lines for the reactions MA and RA and the shear and…

A: To draw ILD

Q: C ㅏ -80- 99 20 Dimensions in mm Help me to get Ix and ly at Neutral axis. Kindly provide Handwritten…

A:

Q: The ABC rod is supported from point B and is in equilibrium with a force F1 = 12KN applied from…

A: Given Data: The equilibrium force F1 is, F1=12 kN The shear strength at pin B is, τs=350 MPa The…

Q: A center-point loading flexural test was performed on a concrete beam with a cross-section of…

A: Given:- b=15.237cm=152.37mm L=span = 18"=457.2mm Failure load =7549.581lb=33582.20939N Modulus of…

Q: The beam shown carries a concentrated load P = 12 kN and a uniformly distributed load w, = 225 N/m.…

A:

Q: ibute to compactive effort in pla

A:

Q: Determine the internal shear and internal moment at point C in terms of P. Be consistent with units.…

A: Given,  Total Span of the beam = 580mm There is A point load acting at the point A.  Our aim is to…

Q: Problems: 1. Determine the forces acting on members BD, CD and CE of the truss loaded as shown using…

A:

Q: Can you show how to do part d I had the first 3 parts done before. I was confused with part D

A: In situ void ratio of top soil (et) = 0.47 Void ratio of borrow soil (eb) = 0.71

Q: 3. A rectangular steel block is subjected to triaxial loading as shown. If v = 0.3 and E = 200 Gpa,…

A: Solution Givan Data ν=0.3E= 200 GPa

Q: Name any four shape that you can identify from the sketch

A: Any sketch such as still life, landscape etc. is prepared with the helps of basics shapes. These…

Q: BED 3 43 x 3.60 BED 2 BATH 2.79 x 358 3.43 x 3.60 W.I.R. 2.33 x 1.06 W.I.L. .93 x 104 W.I.R. 1.35 x…

A: A block in AutoCAD is simply a collection of objects which are grouped together to form a single…

Q: If supports A and E in the given figure are constructed 30 ft and 2.3 in. apart instead of 30 ft…

A: Question is based on the frame supported on hinge support at both ends get deflected. Length of span…

Q: Compute the forces in the diagonal members of the truss shown in the accompanying illustration if…

A: A truss is a construction made up of parts arranged in linked triangles such that the entire…

Q: 1. Although you have not seen this type of table before, you should be able to work through the…

A: Given data : Materials and their properties Material  Cost (£/kg) Density (kg/m3) Yield…

Q: Consider the given figure. Given: P= 20 kips. P D w = 5 kips/ft 4' C 6' - hinge B 6' A

A: Since it is an indeterminant frame we will use an internal hinge to solve for the reaction because…

Q: Bearing Capacity An embankment is to be constructed with granular soil (bulk unit weight = 20 kN/m³)…

A: Given data: Undrained shear strength, C = 25 kPa. Bearing capacity factor = Nc=5.7 Bulk unit weight,…

Q: Determine the required diameter of a plug weld using E60 electrodes on A-36 steel to develop the…

A: Given, Area of the plate  Material of the plate,  Electrode specification,  Find the diameter of a…

Q: A rectangular channel section increases in width from 40 ft to 50 ft in a length of 100 ft. The…

A:

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: The bent bar structure ACDE is supported by ball-and-socket joint at A and E, and by the wire DF.…

A: Given:- A ball-socket-joint is provided at point A The magnitude of the load (P) = 640 N  The…

Q: Correctly Dimension the object using datum dimensioning

A: To show the datum referencing of the drawing

Q: For the figure shown, calculate the elevation of the pressure head at the junction (P). Round off…

A:

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 22 19 38 Ф 18 22…

A: Given Data :

Q: ndwater (which provides baseflow) can be withdraw up in the watershed and through aging how land is…

A:

Q: (5) When calculating the global stability of the beam, @s should be replaced by o's when the global…

A: For global stability of the beam, φb should be replaced by φb when the global stability coefficient…

Q: can you show the sides with dimensioning

A: To show the sides with dimensioning

Q: Draw the influence lines for the reactions at supports A and C, the shear and moment at section B,…

A: Given data  Overhang beam Span length I will use Muller Breslau Principle to solve tgis question.

Q: 15.27 Two reservoirs having a difference of 40 ft in water elevations are connected by a 1.5-mile-…

A: Consider Case 1.   Head Loss=40 ft=12.192 mLength=1 mile=2414.02 mDiameter=0.3048 m

Q: 3. LIMITATION OF AUTHORITY The Architect as the Construction Manager shall not: 3.1 involve himself…

A: Construction project management is a critical discipline that ensures the successful execution of…

Q: 4. Determine the maximum tensile and compressive bending stresses in the beam shown. 2.5 kN/m 5kN…

A:

Q: Consider the given figure. Joints Band Care rigid. Given: w= 2 kips/ft. A D 16' 1 kip/ft B_ 1 kip/ft…

A: As the load acting on AB and CD are equal as well as opposite, So they get cancels each other and…

Q: Please explain step 4 and 5

A: Grade: g1 =3%  g2 =-4% Station of intersection = 3+400 Elevation of intersection = 7600 m Station…

Q: TABULATION Table 1.Reactions of a rigid body Dynamometer Reading (N) Computed Reading (N) Load (N)…

A: solution on trail Aconsider ∑Fy=0RA+RB=4consider ∑Ma=0-RBx900+4x150 =0RB=0.67KN therefore RA=3.33KN

Q: is x correct?

A: Data Availabe: Asked: Centroid

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.