9-1* A beam is loaded and supported as shown in Fig. P9-1. Determine (a) The equation of the elastic curve. Use the desig- nated axes. (b) The deflection at the left end of the beam. (c) The slope at the left end of the beam.

Q: how do you workout the linear interpolation from process 1-2 the step by step working would be…

A: Given data:- Inlet condition of turbine P1 = 8 MPa T1 = 480 °C To find:- the linear interpolation…

Q: the meaning of the graphics below

A: Given: two graphs are shown in graph (a) load is shown on y axis and deformation is shown on x axis.…

Q: draw isometric view using software drawing.

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: c) Consider the fig.2-c below and DRAW the FRONT VIEW, TOP VIEW and APPROPRIATE SIDE VIEW in first…

A: Given isometric view To sketch Orthographic view

Q: Draw the FRONT VIEW, TOP VIEW , SIDE VIEW of the figure below • Draw the SURFACE DEVELOPMENT of the…

A:

Q: Draw the three-dimensional model of the given picture.

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: The distance between a flying drone carrying a laser scanner and a building (Figure 4) is 300m. The…

A:

Q: Draw the isometric view

A: Given orthographic view  Front and top

Q: Q1/ Draw Sectional Front view (Front section), Sectional Side view (Side section),and Draw the…

A:

Q: Using CREO PARAMETRIC, SKETCH THE ISOMETRIC VIEW AND THE MISSING VIEW for the figure 4

A:

Q: raw the multiview projection of the isometr

A:

Q: What effect do frame rate and line rate have on picture quality?

A: Given Data : Frame rate Line rate

Q: Which of the following can be used to building up a three-dimensional prototype model layer by layer…

A: According to the given data We need to find Following can be used to building up a three-dimensional…

Q: Consider an overall drawing made up of objects (full or hollow rectangular parallelepipeds; with or…

A:

Q: Draw the Front view in the direction F, top View in the direction T, of the given machine element…

A: Given: Three dimensional view of a machine component is given with its dimensions. Determine: Draw…

Q: Sketch the orthographic view

A: Solution: The front, top and side views are shown below:

Q: Given the views below, sketch its isometric figure.

A:

Q: Sketch the front view side view isometric view and top view  Use creo parameter drawing to sketch…

A:

Q: Given FRONT AND SIDE VIEW sketch the Top or bottom view NOTE

A:

Q: 7 6 5 сл 4 3 2 1 Work to be done: Reproduce this object in isometric perspective at a scale of 1:50…

A:

Q: A particle moves along the x-axis with velocity given by v(t) = 3t 2 + 6t for time t> 0. If the…

A: Given data: vt=3t2+6t Need to determine the position of the particle at t=1 sec.

Q: sketch the top view ,side view and front view using catia v5, and i need the orthographic view in…

A:

Q: Where can I find the shell option in AutoCAD 3D Modify, solids editing O All option O Solid, solids…

A:

Q: A nearsighted eye is corrected by placing a diverging lens in front of the eye. The lens will create…

A: Individual has a fair point of 39.5 cm

Q: AutoCAD HW • Draw a sectional front view, top view and side view for Hexagonal bolt (M 40mm *…

A: Given Hexagonal bolt To find Views

Q: The three planes of 'orthographic' projection of an object are presented in Figure 1.1 below. Draw…

A: Draw the isometric block according to dimensions of the object as shown in the image:

Q: 3. On the drawing and produced part below, label the following terms: Datum feature symbol Datum…

A: Label the given terms.

Q: Briefly describe which type of axonometric drawing is most commonly used in industry?

A: In industry there are three types of axonometric drawings used they are 1.Isometric Projection 2.…

Q: What term describes a numerical value that can be applied to a dimensional constraint in a technical…

A: Variation process arranging approach is some of the time called an information recovery strategy.…

Q: DIMENSION THE OBJECT SHOWN BELOW. NOTE THAT NOT ALL ORTHOGRAPHIC VIEWS WILL REQUIRE DIMEN- SIONS. DO…

A:

Q: onvert these ortographic views to isometric. Given are the length for you to visualize.

A: Please refer the following image for the isometric view of the given orthographic views.

Q: mechanical engineering : engineering drawing : AutoCAD Can someone please show step by step…

A:

Q: R14 R6- R3- 14 R6 27 012 R14 014 R14

A: what do you want in this

Q: cal graphics a are the preferred method for communicating designs düring a

A: Yes , It is true.

Q: On your new small car, you replace the factory-installed P185/75R14 tires with slightly larger…

A: The old tires code is P185/75R14 where, 185 represents the width of the tire in mm i.e. Width = 185…

Q: 16. The entire top surface on the part below must be flat within 0.5 but each 25 X 25 patch must be…

A: The answer to the above mentioned question is given below

Q: A starship traveling toward you at a speed of 0.5c shines a green light of 500 nm at you. According…

A: Given Data  v=0.5c

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.