85 kN/m2 25 kN/m2 Try solving the following problem: Practice Problem 1: (Repeat practice problem from Module 2, Unit 1 using Mohr's Circle) A soil element is shown in Figure 2.21. Determine the following: a. Maximum and minimum principal stresses В to +1 45 kN/m2 25 kN/m2 40° A b. Normal and shear stresses on plane AB Figure 2.21

85 kN/m2 25 kN/m2 Try solving the following problem: Practice Problem 1: (Repeat practice problem from Module 2, Unit 1 using Mohr's Circle) A soil element is shown in Figure 2.21. Determine the following: a. Maximum and minimum principal stresses В to +1 45 kN/m2 25 kN/m2 40° A b. Normal and shear stresses on plane AB Figure 2.21

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q4: For the soil element shown, compute the stresses acting on the plane inclined by 40° with the horizontal plane then draw Mohr circle and place the stresses with respect to O.P. 20kPa 35kPa 100kPa 300 40°
A soil profi le consists of a clay layer underlain by a sandlayer, as shown in Figure P7.17. If a tube is inserted intothe bottom sand layer and the water level rises to 1 mabove the ground surface, determine the vertical effective stresses and porewater pressures at A, B, and C. IfKo is 0.5, determine the lateral effective and lateral totalstresses at A, B, and C. What is the value of the porewater pressure at A to cause the vertical effective stressthere to be zero?
Numerical Analysis (HW. #1) The vertical stress increment (Ao) due to a point load acting on the surface of linearly elastic medium is given as: 3P23 Ao 27Vr? + z? where P is the magnitude of the load, r is the lateral distance, and z is the depth of the point where the stress is to be calculated. If P = 10g kN and r = using two methods: fixed-point and Newton-Raphson method) the depth z at which the stress increment Ao = 10n kN/m?. (Take g=student group number A=1, B=2, 1.5 m, determine (by C=3, D=4, and E=5, n=student number in his/her group, and & =1x10-6)
Given a soil mass below, calculate the following in kPa:a. Major principal stressb. Normal stress at the failure planec. Shear Stress at the failure plane USE MOHR'S CIRCLE
Subject: Soil Mechanics Please provide a solution and a diagram A granular soil is subjected to a minor principal stress of 200 kN/m2. If the angle of internal friction is 30°. What is the shear stress on the plane of failure? a. 173.2 b. 224.2 c. 200 d. 300
Topic 4:. A soil element is shown in Fig. 1. Determine the following (clearly show calculation procedures): a. Major principal stress b. Minor principal stress c. Normal and shear stress on plane EF d. Use rotation method to locate the normal and shear stress on the plane EF (plot the Mohr's circle by compass and locate normal and shear stress in Fig. 2, 0, = 45 kN/m? y T = 40 kN/m² D, ху C F 0, =150 kN/m? T = 40 kN/m? 22° ху E A В Fig.1. A stressed soil element
Determine the shear stress at points A, B, C and D for the following section. Also determine the maximum shear stress, then plot the shear stress distribution. Given: V = 10 kN. 300 mm - 280 mm 400 mm A B 10 mm 15 mm 395 mm 10 mm
Numerical analysis G=5 N=27
The rectangular bar shown in the figure is subjected to a uniformly distributed axial loading of w = 11 kN/m and a concentrated force of P = 14 kN at B. Determine the magnitude of the maximum normal stress in the bar and its location x. Assume a = 0.9 m, b = 1.1 m, c = 20 mm, and d = 35 mm.
From the following given soil element, using the graphical method (Mohr’s circle),determine 1) the maximum and minimum principal stresses, 2) maximum shear stress,and 3) the normal and shear stresses on plane AB (assume to be the failure surface).Confirm your answer with analytical equations.Please practice more problems from your textbook.
Try solving the following problem: Practice Problem 1: (Repeat practice problem from Module 2, Unit 1 using Pole Method) A soil element is shown in Figure 2.32. Determine the following: a. Maximum and minimum principal stresses b. Normal and shear stresses on plane AB 85 kN/m2 25 kN/m2 B 45 kN/m2 25 kN/m2 40° A Figure 2.32
Magnitude and angle of inclination (from horizontal) of the major and minor principal stresses. 5. A sample of soil is subjected to a stress system as shown in the figure. Determine, a. Maximum shear stress. Stress on a horizontal plane. 5 kN b. с. 10 cm |309 1 kN 20 cm 1 kN 3 kN 20 cm