85 kJ of heat are supplied to a system at constant volume. The system rejects 90 kJ of heat at constant pressure and 20 kJ of work is done on it. The system is brought to its original state by adiabatic process. Determine the adiabatic work. Determine also the value of internal energy at all end states if initial value is 100 kJ. [Ans. W = 15 kJ; U, = 100 kJ, U, = 185 kJ; U, = 115 kJ] %3D %3D %3D %3D

85 kJ of heat are supplied to a system at constant volume. The system rejects 90 kJ of heat at constant pressure and 20 kJ of work is done on it. The system is brought to its original state by adiabatic process. Determine the adiabatic work. Determine also the value of internal energy at all end states if initial value is 100 kJ. [Ans. W = 15 kJ; U, = 100 kJ, U, = 185 kJ; U, = 115 kJ] %3D %3D %3D %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gas with specific volume v₁ = 1 m³/Kg and pressure p₁=1bar in a closed system undergoes a thermodynamic cycle which consists of the following three separate processes: 1->2: Isobaric compression to v₂-0.25 m³/Kg 2->3: Isometric heating. 3->1: Isothermal expansion (pV = constant) to the initial volume. Calculate the specific work produced by the gas per cycle. Present your answer in kJ/kg.
pls answer the given
A 2 kg of steam occupying 0.3 m at 15 bar is expanded according to the law pvl3 = constant to a pressure of %3D 1.5 bar. The work done during the expansion will be
2. A piston-cylinder assembly with stops (see figure) contains 1.54 kg of water initially occupying a volume of 1.25 m at a pressure of 1 bar (State 1). As the water in the assembly is heated, the pressure and temperature in the system remain constant until the piston contacts the stops. In this position (State 2), the quality, x2, is determined to be 92%. Heat continues to be added to the system at a constant volume until the system reaches a pressure of 1.5 bar (State 3). Determine the following quantities: а. X b. V2 (m2) C. W13 (kJ) d. Qu (kJ) e. Plot the results on a P-v diagram, labelling relevant P, T, and v values.
A perfect gas has a value of R=58.8 ft.lb/lb.R and k=1.26. If 20 Btu are added to 5 lb of this gas at constant volume when the initial temperature is 90° F, find (a) ∆U and (b) work for a nonflow process.
Ammonia in a piston-cylinder assembly undergoes two processes in series. Initially, the ammonia is saturated vapour at P₁=1000 kPa. Process 1-2 involves cooling until the piston meets the stops where the position is locked in place at which time quality is x2=75%. The second process from state 2 to state 3, involves heating (at constant volume) until x3=100%. If the mass is 0.45 kg determine: The work for process 2-3 (in kJ). The heat transfer for process 2-3 (in kJ). Sketch the processes on a p-v diagram, what does the area under the curve represent?
Refrigerant 134a at p1 = 30 lbş/in?, T1 = 40°F enters a compressor operating at steady state with a mass flow rate of 250 lb/h and exits as saturated vapor at p2 = 160 lbę/in?. Heat transfer occurs from the compressor to its surroundings, which are at To = 40°F. Changes in kinetic and potential energy can be ignored. The power input to the compressor is 2.5 hp. Determine the heat transfer rate for the compressor, in Btu/hr, and the entropy production rate for the compressor, in Btu/hr-°R.
Nitrogen undergoes an adiabatic process, the pressure volume relationship given as p = (5/V)+1.5 where is in bar and V is in m3. During the process the volume changes from 1.5 x 108 mm3 to 0.05 m3 and the system takes 45 kJ of heat. Determine (i) Work done (i) Work done (ii) Change in internal energy (iii) Final pressure of the gas, if the initial pressure is 1 bar (iv) Final temperature of gas, if the initial temperature is 80°C (v) mass (vi) Change in enthalpy .
In a certain process, the working fluid is cooled until 100 Btu/lbm has been extracted as heat. During this process, 100 ft.·lbf/lbm of fluid is added as work. If the working substance undergoes a change in temperature from 100°F to 50°F, what is the specific heat of the process in Btu/lbm-R?
One kilogram of an ideal gas at 5.5 bar with an initial volume of 0.3 m expands to a final volume of 0.5 m in accordance with the equation 13 pV = C. Find the heat transfer during the process. Take R = 0.287 kJ/kg-K and C¸ = 0.713 kJ/kg-K.
5. Steam expands quasi-statically and isothermally from 800 kPa and 200C to a final pressure of 200 kPa. Determine the work done in kJ/kg.