8/1 When a 3-kg collar is placed upon the pan which is attached to the spring of unknown constant, the additional static deflection of the pan is observed to be 42 mm. Determine the spring constant k in N/m, Ib/in., and Ib/ft. 3 kg 42 mm

8/1 When a 3-kg collar is placed upon the pan which is attached to the spring of unknown constant, the additional static deflection of the pan is observed to be 42 mm. Determine the spring constant k in N/m, Ib/in., and Ib/ft. 3 kg 42 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure on the left, below, shows a non-uniform bent rod with a mass of 5 kg. Your job is to determine the location of the center of gravity of this rod. You design an experiment: you connect a pin and cable to the rod such that it safely stays in static equilibrium under a force P that you apply. Then, you apply forces between 0-100 N, and measure the tension force on the cable using a cable tension meter. The results of your experiment are shown in the figure, on the right. Using this experiment, calculate (approximately) the horizontal distance (x in the figure) between point A and the center of gravity G of the bent rod. B C O I 20 cm 20 cm 60° D 50 cm Tension measurement [N] 60 50 40 30 20 -10 0 10 real data estimated fit 20 30 40 ܐܐܝ 50 P[N] 60 70 80 90 100
A puck weighs 8 lb and rests on the center of the frictionless surface of the ramp supported in equilibrium by ropes AC and BC. Determine the normal force the ramp exerts on the puck as well as the tension in each of the two ropes. g Variable Value Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. a b C d e f g9 36.0 in 45.0 in 13.5 in 27.7 in 45.0 in 18.0 in 35.0 in B The normal force acting on the puck is pounds The tension in rope AC is The tension in rope BC is C pounds pounds
A former student of mechanics wishes to weigh himself t has access only to a scale A with capacity limited to 110 lbs and a small 20- lb spring dynamometer B. With the rig shown he discovers that when he exerts a pull on the rope so that Bregisters 18 lb, the scale A reads 84 lb. What is his correct weight? Answer: Weight= lb
Consider (Figure 1). Block A weighs 50 lb and the platform weighs 18 lb. Figure < 1 of 1 Part A If P = 100 lb, determine the normal force exerted by block A on B. Neglect the weight of the pulleys and bars of the triangular frame. Express your answer in pounds to three significant figures. VAΣ 1 vec N = Submit Provide Feedback Request Answer ? lb
Q1) A man is pulling a spring of stiffness coefficient 8 Ib/in by his hand with the entire arm held horizontally rotating about shoulder joint O; this force acts at the 21° angle is shown. Determine the force exerted by the deltoid muscle on the upper arm at A and x- and y- components of the force reaction at the shoulder joint. The weight of the upper arm Wu = 4.1 Ib, the weight of the lower arm W1 2.4 Ib, and the weight of the hand WH= 0.9 Ib; all these weights act at the locations shown in the figure. the spring extended 1 in only as shown in figure 1. A tensile force in the deltoid muscle prevents the arm from A- 8 Ibin Equilibrium x-1 in Deltoid muscle Fo A YW, YW -5.2 16.5 25.4 Figure 1
A sliding block weighing 50 lb can slide freely within the frictionless slot shown. The spring is undeformed (i.e., not stretched) when it is in a horizontal position. What is the spring constant k if the slider is in equilibrium in the position shown? Show your calculations and result.
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 1000 lb is applied to the tire at point C at an angle of 0 = 17° as shown. Assume the connection of the wheel to member AB is rigid. 1 h₁ K: LOFF 0 W₁ h₂ h3 h4 h5 B W₁₂ AXHIMAL W4 hs: h₂ cc i❀O BY NC SA 2013 Michael Swanbom W3 - W₁ Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value h₁ 6.6 in W1 7.5 in 16.6 in W2 4.6 in 14.6 in W3 8.3 in 10.2 in W4 6.2 in 5.2 in W5 9.7 in
F₁ 2-- Y B y I F₂ 65° 40° F3 Given: F₁ = 2 kN, a = 111.8, 8 = 42", y = 56.15* F₂ = 4 kN F3 1.2991-0.75k kN Choose the best answer: [Select] - X -- A system of three forces acts on particle P. What additional force is required for the particle to be in static equilibrium?
0.50kg 6. If the 2.30 kg uniform beam shown in static equilibrium, what is the magnitude of F, ? 30.0° 5.00 m 40 09
The uniform L-shaped bar pivots freely at point P of the slider, which moves along the horizontal rod. Determine the steady-state value of the angle 0 if (a) a = 0 and (b) a = 0.68 g. For what value of a would the steady-state value of 0 be zero? 2.1 b Answers: (a) a = 0: i (b) a = 0.68g: 0 = i %3D The steady-state value of 0 will be zero when a = i bo
Learning Goal: To use the equations of equilibrium to analyze a system containing a wedge and to determine the necessary applied force to introduce motion into the system. The crate shown is held against wedge B by a spring. The spring is 94.0% of its original uncompressed length 1 = 3.00 m, and the spring constant is given as k = 1650 N/m. The coefficient of static friction at all contacting surfaces is μs = 0.100. The mass of the crate is m = 25.0 kg . The angle is 0 = 14.0°. Neglect the mass of the wedge. Assume the crate only moves in the y direction and that wedge A cannot move. (Figure 1) Figure B < 1 of 1 y L. Part A - Determining the normal force exerted by the crate on the wedge Determine the normal force No that the crate exerts on the wedge when the system is at rest. Express your answer to three significant figures and include the appropriate units. ► View Available Hint(s) Nc= Submit P = Value Part B - Finding the smallest horizontal force P to move the crate upward Submit…
Mastery of learning outcome Advanced.2 evaluation The collar has a mass of 13-kg and slides along the smooth rod. Two springs are attached to it and the ends of the rod as shown. KA 4₁ МАН KB 1₂ 0.25 m Each spring has an uncompressed length of l₁=1.4-m and l₂=2.1-m and stiffnesses k₁=53-N/m and k₂=141-N/m respectively. Determine the velocity that must be subjected to the collar to generate a compression of 0.8 m