8.36 Liquid mercury at 0.25 kg/s is to be heated from 325 to 375 K by passing it through a 25-mm-diameter tube whose surface is maintained at 400 K. Calculate the required tube length by using an appropriate liquid metal convection heat transfer correlation. Compare your result with that which would have been obtained by using a correlation appropriate for Pr z 0.7.

8.36 Liquid mercury at 0.25 kg/s is to be heated from 325 to 375 K by passing it through a 25-mm-diameter tube whose surface is maintained at 400 K. Calculate the required tube length by using an appropriate liquid metal convection heat transfer correlation. Compare your result with that which would have been obtained by using a correlation appropriate for Pr z 0.7.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the heat transfer coefficient for forced convection local boiling of water in a vertical pipe at 8 atmospheres pressure, 12°C surface superheat.
molten salt at 920 K. Data for molten salt: 10 K¹: (920 K) 1.65 x 10³ N s m². 8.20 A steel rod (25 mm diameter and 0.6 m length) is heated vertically in a large bath of Calculate the heat transfer coefficient when the bar is at 640 K. = 870 J kg K¹; p = 3200 kg m³; ß = 2 x k = 86 W m¹ K¹; C, : 1.03 x 10³ N s m²; n(780 K) = 1.24 x 10³ N s m²; n(640 K) =
Saturated, pure steam at a temperature of 170 oC condenses on the outer surface of avertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at auniform temperature of 150 oC.Calculate:a) the local film condensation heat-transfer coefficient at the bottom of the tube. b) the average condensation heat-transfer coefficient over the entire length of the tube. c) the total condensation rate at the tube surface.
A shell-and-tube heat exchanger is used to cool compressed liquid methanol from 176 °F to 104 °F. The methanol flows on the shell side of the exchanger. The coolant is water that rises in temperature from 50 °F to 86 °F and flows within the tubes at a rate of 68.9 kg s1. Finding the appropriate thermophysical data and applying the proper equations, you are required to do the following: (a) Calculate i) methanol mass flow rate in the exchanger, ii) methanol volumetric flowrate at the inlet of the exchanger. (b) i) For the counter-current flow of the fluids calculate the log temperature difference, ii) explain the purpose of calculating this difference, iii) explain, quantitatively, why is the counter-current flow in heat exchangers preferred to co-current flow. mean
Water is to be heated from 35 °C to 65 °C in a rough tube with a relative roughness of 0.001. The tube has an electric heater provides a constant heat flux such that the tube average wall temperature is 20 °C above the average water bulk temperature. The Reynolds number used for calculating the heat-transfer coefficient is 100,000. Calculate the length of tube required for heating, expressed in meters, if the tube has a diameter of 1 cm.
Air is to be heated by passing it across the tubes of an in-line tube bundle consisting of 8 rows of 25 mm OD tubes in the direction of flow and 10 tubes in each row normal to the flow. Air approaches the tube bank in the normal direction at 30 °C and 1 atm with a mean velocity of 10 m/s. The tube spacing is 37.5 mm in both parallel and normal to the flow. Calculate the heat transfer from the bundle per m of length when the tube surface temperature is 90 °C.
A liquid is heated from 20 to 70 oC as it flows at 0.025 kg/s through a steel tube of 10 mm and 12m long. A uniform heat flux is maintained on the tube surface. Using the following liquid properties ρ = 1000 kg/m3, Cp = 4100 J/kg.K, k = 0.45 W/m.K, Pr = 10, μ = 2x10-3 kg/s.m. Calculate the average heat flux on the tube. Calculate the heat transfer coefficient at end of tube Calculate the surface temperature at exit and the heat transfer coefficient for first 1m of pipe?
In the final stages of production, a pharmaceutical is sterilized by heating it from 25 to 75°C as it moves at 0.21 m/s through a straight thin-walled stainless steel tube of 12.7-mm diameter. A uniform heat flux is maintained by an electric resistance heater wrapped around the outer surface of the tube. If the tube is 10 m long, what is the required heat flux? If fluid enters the tube with a fully developed velocity profile and a uniform temperature profile, what is the surface temperature at the tube exit? Fluid properties may be approximated as p = 1000 kg/m³, c, = 4000 J/kg-K, µ = 2x 103 kg/s-m, k = 0.8 W/m-K, and Pr = 10. Determine the required heat flux, W/m². q! = i W/m? Determine the surface temperature at the tube exit, in °C. i °C S,0
Q) Compare the heat transfer coefficients under the following conditions (Assume flow is turbulent). (1) Two fold increase in the diameter of the tube; the flow velocity is maintained constant by a change in the rate of liquid flow. (2) Two fold increase in the flow velocity by varying the mass flow rate. Comment on. the results.
Water going into a pipe with a tempeture of T1 and going out T2 . ambient tempeture is T0. flow rate q. Develop an expression for T2 ( based on heat transfer) Length of the pipe Lh0 - convective heat transfer coefficient of the airhW -convective heat transfer coefficient of the waterk- pipe thermal conductivity (W/m·K)d – pipe diameter Use any other varilable that you need and can be found online easily .
2-D: A fin may be manufactured as an integral part of a surface by using a casting or extrusion process, or it may be separately brazed or adhered to the surface. From thermal considerations, which option is preferred? 2-E: What is the difference between steady-state and transient heat transfer processes? Give an example for each of them. 2-F: What is the physical interpretation of the Biot number? 2-G: For flow over a flat plate, sketch variation of local convective heat transfer coefficient, h(x), versus the distance along the plate x for laminar, transition, and turbulent flow regimes.
A shell-and-tube heat exchanger is used to cool compressed liquid methanol from 176 °F to 104 °F. The methanol flows on the shell side of the exchanger. The coolant is water that rises in temperature from 50 °F to 86 °F and flows within the tubes at a rate of 68.9 kg s-1. Finding the appropriate thermophysical data and applying the proper equations, you are required to do the following: