8. The figure shows a lateral pipe fitting in a vertical plane. Calculate the horizontal (x) and vertical (y) components of force required to hold the lateral fitting stationary. Neglect gravitational force. The following measurements were recorded for water following in the fitting. Section Diameter Area (ft2) Flowrate Velocity Pressure 1.63 cfs 34.0 psi 1 3 4.0 in 4.0 3.0 1.0 35.0 5K 33.5 C.V. Force R₂ R₂

8. The figure shows a lateral pipe fitting in a vertical plane. Calculate the horizontal (x) and vertical (y) components of force required to hold the lateral fitting stationary. Neglect gravitational force. The following measurements were recorded for water following in the fitting. Section Diameter Area (ft2) Flowrate Velocity Pressure 1.63 cfs 34.0 psi 1 3 4.0 in 4.0 3.0 1.0 35.0 5K 33.5 C.V. Force R₂ R₂

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3. Referring to the jet-impact test shown in Figure 3: The following tables show one measurement for the 90o-deflection plate. Referring to the lab manual, complete the missing columns in the tables.
Show complete solution. Units must be included in all calculations. All numerical values should be rounded off to the nearestthousandths. 3.At section 1 of a pipe system carrying water the velocity is 3.0 fps and the diameter is 2.0 ft. At section 2 thediameter is 3.0 ft. Find the discharge and velocity at section 2.
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154mm) at point A to 18 in (429 mm) at point B. The volumetric flow rate is 5.0 *3/sec (130 L/s). The respecLve pressures at points A and B are 10 psia (70 kPa) and 7 psia (48.3 kPa). All lossesare insignificant. What are the direcLon of flow and velocity at point A? (A) 3.2 */sec (1 m/s); from A to B(B) 25 */sec (7.0 m/s); from A to B(C) 3.2 */sec (1 m/s); from B to A(D) 25 */sec (7.5 m/s); from A to B
Solve just point 3 please!
Don't give wrong answer please
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
Table below shows the test data of the flow velocity (Q) and pressure drop (4P). Knowing that there is an offset of 0.03 in the flow measurement, the relation between the measured flow velocity and pressure drop is thus described as Q = avAP + 0.02, find the constant a for the best fit using Least- Square Method. (You can check your answer using excel, but will get NO point with only a value from excel without any procedures). Q (in³/sec) 0.17 0.20 0.26 AP (psi) 97 153 262
answer all please
Py Flow FIGURE 6.2 Portion of a fluid distribution system showing variations in velocity, pressure, and elevation. Reference level 2.
Water is flowing steadily at an average velocity of 6 m/s in a pipeline of diameter 50 mm. Somewhere along the pipeline, the diameter of the pipeline is reduced by a fitting to a diameter of 20 mm. Calculate the average velocity of flow in the 20 mm diameter section of pipe. [Answers in m/s, Numerical value only] Answer: Next page OSearch for anything
Flow (m³ /h) 1 1.5 2 2.5 Pressure difference Ap (bar) 0.005 0.012 0.021 0.034 Kinematic viscosity 10-6 m?/s V (Rough Pipe Radius = 25mm) (Rough Pipe length =L=80cm) Question: An experiment is made using different flow rates in a pipe and pressure differences are given according to the given flow values. According to these; 1. Calculate the pipe roughness height ( e ). 2. Calculate the Reynolds value. 3. Calculate the coefficient of friction f from the Darcy-Weisbach equation. 4. Briefly describe the equations you use and the reasons for using them.
3. A seamless steel pipe carries 2000 m³ of steam per hour at a pressure of 1.2 N/mm². The velocity of flow is 28 m/s. Assuming the tensile stress as 40 MPa, find the inside diameter of the pipe and its wall thickness. [Ans. 160 mm; 5.4 mm] 4. Compute the dimensions of a flanged cast iron pipe 200 mm in diameter to carry a pressure of 0.7 N/mm².