E.Write the Given and what is being asked..Write your complete solution.1. Round off your answers into TWO decimal places.. BOX your final answer and don't forget the units.5.Avoid erasures 8. Determine the reluctance of a piece of cast steel of length150 mm and cross-sectional area 1800 mm2 when therelative permeability is 4000. Find also the absolutepermeability of the cast steel.

Answered: Image /qna-images/answer/dd9f6c2f-e07c-4a7a-ab50-5b22eff9ec46.jpg

Answered: 8. Determine the reluctance of a piece…

8. Determine the reluctance of a piece of cast ste 150 mm and cross-sectional area 1800 mm2 when the relative permeability is 4000. Find also the absolute permeability of the cast steel.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A square bar of 1 cm dimension and 30 cm long formed into a ring leaving an air gap at both ends of…

Q: certain laminated core has a permeability of 3,150. The length is 4.85 cm and the cross section is…

A: We need to find out reluctance .

Q: A steel har needs 2000 AT to magnetise it. The voltage required for the magnetising coil of i00…

A: Given, Magnetomotive force, MMF=2000 AT. Number of turns, N = 100 turns. Resistance, R=20 Ω.

Q: For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 11.6-0-11.6 V…

A: Given data:

Q: Which of the following statement is true? a. Angle between load voltage and load current in a pure…

A: Solution:- Let's consider a capacitor C connected to load with capacitance C.C is connected as load.…

Q: 3. A coil consist area ot 0.8 mm? The mean 2.000 turns of copper wire hav ing length par sectional…

Q: QUESTION 7 Match Collumn A and Collumn 8? Properties of Metal v Britleness A. the property of a…

Q: 1.Consider the magnetic core below.All dimensions are shown on the figure. The core is made up of…

Q: Q2/ Looking at the directions of the four diodes .What is the current through 80 2 resistor in the…

Q: (c) Detemine the reluctance of a piece of mumetal of length 150 mm and a cross-sectional area 1800…

A: In this question , we will find reluctance of a piece of material..

Q: A solenoid is 1 Cm long with a diameter of 0.5 Cm. The core is SiFe with a relative permeability of…

A: Length of solenoid Diamter Current I = 100 mA.Relative permeability Magnetic field

Q: write a Conclusion about Clamper

A: Clampers otherwise called as Voltage Doublers or Level Shifters. Clamping circuits are designed to…

Q: Q-3 A) If tension surface of the globule in transformer oil is 0.05N/m, radius of globule is 1um,…

A: The critical electric field at which the globule becomes unstable is given by the expression as…

Q: A copper conductor has a diameter of 0.6 in and it is 1200 ft long. Assume that it carries a total…

Q: What is dimensional formula of conductivity ,it's unit and answer in well manner step wise and also…

A: The dimensional formula for conductivity is derived as given below, P=i2R P=i2ρlA On rearranging,…

Q: What is Ohms law? Explain with examples

A: Define Ohm's Law

Q: A resistance strain gauge with a gauge factor of 2.0 is fastened to a steel member subjected to a…

A: Given- Gauge factor GF=2, Stress S=100 N/mm2, Modulus of elasticity of steel- E=2×105 N/mm2, To…

Q: What current does the ammeter read in milliamperes? Given: Solution:

Q: The definition of Current in machine

A: An electrical machine works on the principle of electro-mechanical energy conversion. Any electrical…

Q: These Insulators are used when equal Voltage is required across each Insulator unit. O A. RADING…

A: Suspension insulator is used as insulator string. For example string of 4 conductors

Q: What are the majority carriers in a P type material

A: P type materials are formed by dopiing pure semiconductor with third group elements.

Q: For the network shown in Figure B22, assume E- 12V, Diode Di as silicon and D2 Germanium, RI-1.5KQ…

Q: 21) what is core and cladding?

A: Optical fibre is basically made up of three components namely, core, cladding and buffer. Difference…

Q: Discuss how impressed current can prevent the corrision of metals.

Q: hat are the majority carriers in a “N” type material & will the material be a positive or negative…

A: there are two type of material present based on the charge carriers, n-type and p-type

Q: V1 D1 D2 20 V R2 10 R. R1 20

Q: The full-scale deflecting torque of a 20 A moving-iron ammeter is 6 × 10³5 N-m. What is the rate of…

Q: What the need of testing insulators in the laboratory? Why insulators most likely to fail at lower…

A: Insulators are the substances that don't conduct electricity at all.

Q: The resistance of the wire is 126.48-N at 1000C and 100-2 at 300C. Determine the temperature…

A: Given data: R100° C=126.48 ΩR30° C=100 ΩΔT1=100° CΔT2=30° C The expression for the temperature…

Q: büt3. Considering the stress-strain graph represented in the figure below, define the following…

A: The properties of material given are- 1) Ductility 2) Resilience 3) Toughness

Q: 11. There is 900 mA of current through a wire with 40 turns. What is the reluctance of the circuit…

Q: 1. What are the two necessary conditions for a thyristor to begin conduction? 2. Once a thyristor…

A: The condition for a thyristor to begin conduction is, The conduction happens when the anode…

Q: What is meant by sheet resistivity, and how does this differ from the resistivity of a material?…

A: Discuss about sheet resistivity and how does this differ from the resistivity of a material. Also…

Q: Ferromagnetic materials have this characteristic. A. A relative permeability slightly less than…

A: We are asked to identify characteristics of ferromagnetic materials from the given options.

Q: The 'skin effecť is a phenomenon experienced when current flows through a metal. Which two of the…

Q: What should be the reluctance of the laminated steel sheet having a permeability of 3000 with a…

A: We need to select correct option for reluctance for given sheet.

Q: Electric resistance seam welding uses . . electrodes. (a) pointed (b) disc (c) flat (d) domed

A: According to the question we have to find electric resistance seam welding.

Q: Which of the following is not true for ferromagnetic materials? Please choose one: a. High ? m…

A: Properties of ferromagnetic material: Above the Curie temperature, they lose their non-linear…

Concept explainers

DC Generator

An electromechanical machine which converts input mechanical energy to respective output electric energy is called a generator.

Question

E.Write the Given and what is being asked.
.Write your complete solution.
1. Round off your answers into TWO decimal places.
. BOX your final answer and don't forget the units.
5.Avoid erasures

8. Determine the reluctance of a piece of cast steel of length
150 mm and cross-sectional area 1800 mm2 when the
relative permeability is 4000. Find also the absolute
permeability of the cast steel.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Need correct solution with proper explanation why you chose the specific option. The solution should be neatly written on paper
DL
Problem 1.11 A large steel plate under uniform applied tensile stress contains two cracks, both of which are remote from the edges of the plate and from each other. One is 12 mm in length and is inclined at an angle a= 30°, the other is 15 mm in length and is inclined at an angle B= 45° (figure 1.15). The steel has fracture toughness of Kie = 23 MPa/m and Ke=15 MPa/m. a) Calculate the fracture stress of the plate and state which of the two cracks will cause failure and in which failure mode. (1) པ། Figure 1.15: Finite width thin plate under uniform applied smile stress with two cracks
a) A coil consist of 2000 turns of copper wire having a cross sectional area of 0.8mm?. The mean length per turn is 80 cm and the resistivity of copper is 0.02µN-m. Find the resistance of the coil and power absorbed by the coil when connected across 110V D.C supply.
What does PVC stand for? O A. Polyvinyl Chloride O B. Perovinyl Chloride O C. Pure Vinyl Compound D. Polyvitamin Chlorine
22
. Using the I – V curves how are ohmic materials different from non-ohmic materials
subject
If we stretch a copper rod, making it 0.1% longer, how much will its resistance change? What behavior do we assume for copper in deformation?
Calculate the relative permeability of an iron ring has mean diameter of 15 cm, a cross section of 1.4 cm and has a radial gap of 0.4 mm cut in it. It is uniformly wound with 1500 turns of insulated wire and a current of 1 A produces a flux of 0.4 mwb across the gap. Assume there is no magnetic leakage.
None
b) A certain winding made up of copper has a resistance of 100 Q at room temperature. If resistance temperature coefficient of copper at 0 C° is 0.00428/C°, calculate the winding resistance if temperature is increased to 45 C°. Assume room temperature as 25 C°.