8. Design a shaft and flange for a Diesel engine in which protected type of flange coupling is to be adopted for power transmission. The following data is available for design : Power of engine = 75 kW; speed of engine = 200 r.p.m.; maximum permissible stress in shaft = 40 MPa; maximum permissible twist in shaft = 1° in length of shaft equal to 30 times the diameter of shaft; maximum torque = 1.25 × mean torque; pitch circle diameter of bolts = 3 x diameter of shaft; maximum permissible stress in bolts = 20 MPa. Find out: 1. Diameter of shaft, 2. number of bolts, and 3. diameter of bolts.

8. Design a shaft and flange for a Diesel engine in which protected type of flange coupling is to be adopted for power transmission. The following data is available for design : Power of engine = 75 kW; speed of engine = 200 r.p.m.; maximum permissible stress in shaft = 40 MPa; maximum permissible twist in shaft = 1° in length of shaft equal to 30 times the diameter of shaft; maximum torque = 1.25 × mean torque; pitch circle diameter of bolts = 3 x diameter of shaft; maximum permissible stress in bolts = 20 MPa. Find out: 1. Diameter of shaft, 2. number of bolts, and 3. diameter of bolts.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Example. Design a plain carbon steel Centre crankshaft for a single acting four stroke single cylinder engine for the following data: Bore=400 mm; Stroke = 600 mm; Engine speed = 200 r.p.m.; Mean effective pressure = 0.5 N/mm²; Maximum combustion pressure = 2.5 N/mm²; Weight of flywheel used as a pulley = 50 kN; Total belt pull = 6.5 kN. When the crank has turned through 35° from the top dead centre, the pressure on the piston is IN/mm² and the torque on the crank is maximum. The ratio of the connecting rod length to the crank radius is 5. Assume any other data required for the design.
Parvinbhai
%AY l. +11:47 The shaft shown below consists of three segments AB, BC and CD is subjected to the three torques T1=114 N.m, T2=245 N.m and T3=441 N.m. The length of each segment is L1=0.71 m, L2=0.31 m and L3=0.43 m. The diameter of each segment is d1=46 mm, d2=97 mm and d3=131 mm. The material have modulus of rigidity G=143 Gpa. Answer the following questions d3 T3 d2 T2 T1 d1 в 1 - L3 L2 L1 The polar moment of inertia of the segment AB is 2.89125E-05 2.5096E-05 3.7326E-05 2.85944E-05 2.93461E-05 Clear selection
A connecting rod for an I.C. engine running at 1800 r.p.m. and developing a maximum pressure of 3.15 MPa. The diameter of the piston is 100 mm; mass of the reciprocating parts per cylinder 2.25 kg; length of connecting rod 380 mm; stroke of piston 190 mm and compression ratio 6:1. Take a factor of safety of 6 for the design. Take length to diameter ratio for big end bearing as 1.3 and small end bearing as 2 and the corresponding bearing pressures as 10 MPa and 15 MPa. The density of material of the rod may be taken as 8000 kg/m³ and the allowable stress in the bolts as 60 MPa and in cap as 80 MPa. The rod is to be of I-section for which you can choose your own proportions. Calculate the dimension of I- section of the connecting rod.
Hence v = 44.1 m/s N = 1500 x 44.1/23.6 = 2800 rev/min. EXAMPLE 6. Two parallel shafts connected by a cross belt have the diameters of pulleys 40cm and 60cm respectively. The direction of rotation of the driven shaft is required to be reversed, by changing over to an open belt drive. State if the same belt can be used. If not, what is the remedy? Assume that the center distance between the shaft is fixed at 6meters. CHAIN DRIVE CLASSIFICATION OF CHAIN (a) Hoist chains as shown below: These are used for hoists, cranes, block and tackle pulley arrangement.
4. A bearing is subjected to a radial force of 8kN and a thrust force of 3 kN. The values of X and Y factors are 0.56 and 1.5 respectively. The shaft rotates at 1200 RPM. The diameter of the shaft is 75mm and Bearing no. 6315 (C= 112000N) is selected for this application. Estimate the life of this bearing with 90% reliability.
1. A six-cylinder two-stroke engine with a compression ratio = 9 produces a torque of 1100 Nm at a speed of 2100 rpm. It has a bore bof 123 mm and a stroke s of 127 mm. (a) What is the displacement volume and the clearance volume of a cylinder? (b) What is the engine bmep, brake power, and mean piston speed?
A gearset has a module of 5 mm, a 20 degree pressure angle, and a 24-tooth cast iron spur pinion driving a 48-tooth cast-iron gear. The pinion is to rotate at 500 rev/min. The objective is to calculate the power in kwatt that can be transmitted by the gearset.. In this case, the cast iron, cast profile gears and the velocity factor must be calculated from the Barth equation. The bending stress is limited to 50 MPa and the facewidth is 60 mm. The velocity factor is considered to be significant and must be used in stress calculations. Calculate the power in kwatt the gearset can transmit using the Lewis bending equation. Note: in this case the stress MUST be modified by the velocity factor, Kv.
Learning Goal: To become familiar with and apply the concepts of maximum sustainable torque and power to solid and hollow circular shafts. A solid circular shaft and a tubular shaft, both with the same outer radius of c=co = 13.0 mm, are being considered for a particular design. The tubular shaft has an inner radius of ci = 8.00 mm. The shafts are to be powered by a motor operating at a frequency of f = 3.00 Hz and are to handle an attached load. Assume the cross-sections are uniform throughout the lengths of the shafts and that the materials have allowable shear stress of τallow = 96.0 MPa. PART A: Determine the maximum sustainable torque that the solid shaft can handle. PART B: Determine the maximum sustainable torque that the tubular shaft can handle. PART C: Determine the maximum sustainable power that the solid circular shaft can handle without failing. PART D: Determine the maximum sustainable power that the tubular circular shaft can handle without failing.
2. A flat belt runs over two pulleys of diameter 800 mm and 1,400 mm with center distance 24 m. A power of 90 kW is transmitted from 800 mm pulley. Assuming slip as 2 per cent and design stress for belt material 2.8 MPa, calculate the size of flat belt. Assume belt velocity 20 m/s, coefficient of friction 0.3. and safe stress 2.1 MPa. [t = 15 mm: h 250 3. Select a
An engine of 175 mm bore and 375 mm stroke is governed by hit and miss type governor to 220 rpm. With a fixed setting of the gas supply and ignition advance, indicator diagrams gave the following values of mean effective pressure. Firing, positive loop 5.7 bar, negative loop 0.25 bar; missing negative loop 0.42 bar. When developing 6 kW the explosions were 100 per minute and the gas used was 0.1 m per minute. Calculate the friction power and assuming uniform gas supply per explosion, find the gas consumption per minute at no load.
You are asked to design a four cylinder four-stroke compression ignition engine for light trucks, which is required to provide a maximum brake torque of (2.000x10^2) Nm at the rated speed of (4.50x10^3) rpm. The bore (B)/stroke (L) ratio is required to be (9.0000x10^-1). Given that the bmep of the engine is assumed to be (1.0000x10^3) KPa, find its stroke (L). The answer should be in the unit of meter with 3 significant figures.