8. Assume a transmission line with Z = 75 – j25N and Zo = 502. Using the smith chart, find i) the normalised load impedance; ii) the corresponding reflection coefficient; iii) the standing wave ratio; iv) the distance between the load and the first voltage maximum; v) the distance between the load and the first voltage minimum; vi) the normalised admit- tance; vii) the input impedance at 0.4X from the load. (Show all steps on the Smith chart)

8. Assume a transmission line with Z = 75 – j25N and Zo = 502. Using the smith chart, find i) the normalised load impedance; ii) the corresponding reflection coefficient; iii) the standing wave ratio; iv) the distance between the load and the first voltage maximum; v) the distance between the load and the first voltage minimum; vi) the normalised admit- tance; vii) the input impedance at 0.4X from the load. (Show all steps on the Smith chart)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

q
The standing wave on a transmission line is caused by: Select one: a. The interference between Vt and b. The interference between V(z) and Vt. c. The interference between V and d. The interference between V(z) and Vo. e. The interference between Vt and O f. The interference between V and I. g. The interference between V(z) and h. The interference between V(2) and
What is the required bandwidth according to the Carson's rule, when a 100 MHz carrier is modulated with a sinusoidal signal at 1KHz, the maximum frequency deviation being 50 KHz.
pls show complete solution. Discuss the propagation of EM wave in a conductor,
A transmission line of characteristic impedance of Zo=50 ohm with length of A/4 loaded by a load impedance of 150ohm find 1- the load reflection coefficient 2- the standing wave ratio (SWR)
Please help ASAP with a handwritten answer Two identical wave generators in a ripple tank produce an interference pattern using a wavelength of 2.58cm. Point M is on the first nodal line. This point is 12.4 cm from source 1. a) How far is point M from the other source? b) Point N is also on a nodal line. It is 21.8cm from one source and 15.4cm from the other. On Which nodal line is N located? Include a sketch.
1. Matching of a transmission line with a characteristic impedance (Zo) and a load impedance (ZR) can be obtained when (a) ZR=0.5ZO (b) ZR-2Z0 (c) ZR-Zo (d) ZR=0 2. Standing wave ratio (S) for a short circuit load connected to a transmission line is equal to (a) S=0 (b) S=-1 (c) S= Infinity (d) S=1 3. Any transmission line repeats its impedance, voltage, and current characteristics every (Where n-0, 1, 2, 3....etc.) (b) nλ/3 (a) nλ/2 (c) ni/5 (d) nλ/6 4. In smith chart, moving in the clockwise direction means moving a) From load to generator b) From generator to load 5. In Crank diagram, moving in the clockwise direction from the load to the source can be evaluated using the formula a) +j2Bd b)-j3Bx c) -j2Bd d)-j2Bx
Solve for the (a) total resistance and (b) total current of a 40 V ac voltage, with 100 Hz frequency, connected to resistors shown in the figure. Calculate for the (c) period, (d) wavelength, (e) VM, (f) IM, (g) VP-P, (h) IP-P, (i) VAVE, and (j) IAVE
4. Again, from the zigzag-path waveguiding model, explain why the group velocity is always slower than the phase velocity in a waveguide with a cutoff frequency.
The answer according to the book is 5.57 MW
This question is about microwave material. I need a solution as soon as possible, please
Solve the cutoff frequency for the first mode and third mode of WR430 waveguide.