11.a. A fiber link has a polarization mode dispersion of 4.2 ps/√km. The fiber link is 5 km. What's the total polarization mode dispersion in this fiber? A. 1.9 ps B. 9.4 ps C. 0.84 ps D. 21 ps 11.b. A transceiver has an extinction ratio of 6 in a fiber link. What's the extinction ratio power penalty? A. 1.5 dB B. 7.8 dB C. 1.1 dB D. 6 dB

Q: Design a microstrip line on a 0.5 mm alumina substrate (er = 9.9, tan o = 0.001) for a 50…

A:

Q: 3.4.3 A IS km optical fiber link uses fiber with a loss of 1.5 dB km". The fiber is jointed every…

A:

Q: just part two only

A: The observed melting range of 202.8-206.6°C suggests that the obtained product is likely a pair of…

Q: 2. Explain why a hollow waveguide can't support a TEM mode of an electromagnetic wave? Given a…

A: We need to explain  why a hollow waveguide can't support a TEM mode of an electromagnetic wave. We…

Q: Consider a step index multimode fiber with a core diameter of (9.0000x10^1) (µm), a core refractive…

A: According to the question,Consider a step index multimode fiber with a core diameter of…

Q: 1. Solve for the (a) total resistance and (b) total current of a 40 V AC voltage, with 100 Hz…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Derive the power spectrum function f(w) for the following processes. (a) xt = :-0.7t-2 + Wt. (b) xt…

A: We to derive the power spectrum function fx(ω) for the following process. a) xt=-0.7xt-2+wt b)…

Q: An oscilloscope is to be have anipt resistance of 8Mrgasensitivity of and attenuation factord…

A:

Q: Consider a slap of silicon which is illuminated with photons having a wavelength of 0.8 µm. The…

A: To Calculate the thickness of the conductor

Q: A T-junction power divider is the simplest network that can be used for power division or power…

A:

Q: A 2.28-cm by 1.01-cm waveguide is filled with a dielectric material with er = 2.25. The…

A: Wave is function of space and time. The mode at which waveguide have lowest frequency is said to be…

Q: Find the half power beam width HPBW and first null beamwidth FNBW of the field pattern E(0) cos(20),…

A: According to the question, for the given field pattern Eθ=cos22θ We need to find HPBW, and FNBW.

Q: roblem 1. Propagation loss and bending loss Assume you design a waveguide nat is 3 mm long and…

A:

Q: Q9) calculate the percentage power saving when a carrier and one of the sidebands are suppressed in…

A:

Q: In an FM broadcast transmitter, the carrier signal is being deviated between 103.505MHz and…

A:

Q: What is the value of the input impedance half wavelength from the load? a. ZL b. minimum c. maximum…

A: Half wavelength line is said to be load reflection line. It means the load impedance is reflected at…

Q: 6. Compute the inductance of a coil formed by 10 turns of AWG 26 copper wire on a 5mm air core…

A: no. of turns (n)=10 length of copper wire l=5mm diameter of copper wire d=5mm area of copper coil…

Q: Q3: A sinusoidally modulated AM waveform is shown below, Determine: 1. Peak amplitude of the upper…

A: Based on the bartleby guidelines solved first three subparts kindly repost the remaining questions…

Q: The wavelength of life used in the transmitter is a. 680 nm b. 670nm c. 665 nm d. None of above

A: Basic problem on wavelength of the transmitter.  Look below for the solution..

Q: The available wavelength band for silicon based fiber consists of O-band(1260 to 1360 nm),  E-band…

A: The answer as given below:

Q: The HVL of a photon beam with 0.693 1/mm linear attenuation coefficient

A:

Q: A 10-MHz sinusoidal carrier wave of amplitude 10 mV is modulated by a 5 kHz sinusoidal audio signal…

A: Amplitude modulation of the carrier signal is varied with an amplitude of modulating signal keeping…

Q: (6) Without modulation, the carrier power in an AM transmitter is 5 KW. This carrier is modulated by…

A: AM transmitter: The transmitter is a device that transmitter or sends the radio wave that wave has…

Q: A superheterodyne receiver is to tune the range 88.1MHz to 107.1MHz. The RF circuit inductance is…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 2. Up to this point, you have relied on the boundary conditions to solve the mode fields in a…

A: What is the most-used boundary condition you used for a structure with conducting boundaries?

Q: Please i need the answer of this question in RF

A: Given: A coil formed by 10 turns of AWG copper wire on 5mm air core assuming its length 5mm and at…

Q: A rectangular waveguide of internal dimensions a = 4 cm and b 3 cm) is to be operated in TE mode The…

A: Wave is function of space and time. The mode at which waveguide have lowest frequency is said to be…

Q: Solve for the (a) total resistance and (b) total current of a 42 V ac voltage, with 100 Hz…

A: In this question we will find total resistance and current, peak values...

Q: in the TE10 mode propagation in air-filled rectangular waveguide, if the broader dimension of the…

A: Given data  Dimension of wave guide ,a=30mm

Q: Sketch and identify the components in an eddy current inspection configuration. Explain the…

A: Eddy current is induced within conductors with change in magnetic field. It produces loss of energy…

Q: Calculate the distance (cm) that the moving mirror needs to travel in order to "barely resolve" the…

A: Given:-

Q: A rectangular waveguide has a dimension of (3X2) cm is used to transmit a signal of 9 GHz. Determine…

A: Given: A rectangular wave-guide used in dominant mode. Dimensions, a=3 cm and b=2 cm Frequency, f=9…

Q: For 860 MHz carrier frequency and for the geometry and

A:

Q: 4.a. What's the typically acceptable maximum BER value in a multimode fiber? A. 10–7 B. 10–6 C. 10–9…

A: Answer 4(a), The typically acceptable maximum BER value in a multimode fiber is 10-9. This value is…

Q: :Q2. Explain the following for the VHF :Frequency :Wavelength :Propagation Via

A: given VHF

Q: a) Define Guide wavelength with the formula?

A: According to the Bartleyby guidelines “Since you have asked multiple question, we will solve the…

Q: b) ) What is the maximum core size allowed for single mode operation? Answer:

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: Which of the following statements is not true about the linear polarization technique? a)…

A: (a) The voltage applied to the metal is very less, that is less than 30 mV. Hence, (a) is not true.