8. Analyze and use Cantilever Method to determine the force and moment of the given below. Summarize and compare the process and results of both methods in bullet form. Assume the area of all the columns are equal. The baseplates connecting all columns to the foundation can be treated as fixed supports. Provide free body diagram.

8. Analyze and use Cantilever Method to determine the force and moment of the given below. Summarize and compare the process and results of both methods in bullet form. Assume the area of all the columns are equal. The baseplates connecting all columns to the foundation can be treated as fixed supports. Provide free body diagram.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Mansard roof truss is loaded as shown. Determine the force in members EG in kN. P = 6.2 kN and x = 4.0 m. Write numerical value only in 2 decimal places.
The maximum force any member can support is 24 kN in tension and 35 kN in compression, determine the largest permissible mass “m” which may be supported by the truss. Hint: use the method of joints to calculate all of the member forces in terms of the weight (say “w”); then choose the largest positive and negative member forces to determine m = w/g. There is a “rocker” support at “E”; this is the same as a roller support
Using the method of joints, determine the internal forces in each member of the truss. Show your results in a sketch of the truss along with the magnitudes of the internal forces. Indicate whether each member is in tension or compression. A 40 kN B F 20 kN 60 kN ↓c с G 4 at 8 m = 32 m - 30 kN H D E 6 m
es ! Required information Consider a truss shown below. Given that F= 0.85 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B D F H J ANNA C E G THIN 1m 1m 1m 1 m 1m 1 m 2m Α K L Find the force supported by member FH. (Round the final answer to four decimal places. Include a minus sign if necessary.) The force supported by member FH is kN.
The steel truss (E =200 GPa) shown in figure below has a cross-sectional area of 1920 mm². Determine: a. The largest allowable load F if the change in length of member BD is not to exceed 1.6 mm and a factor of safety of 2.5. b. The displacement of support D due to the load calculated in part a. 5m 6m A C F
Determine the forces in members BF,BC,EF in the truss shown. Solve using Method of sections. Quickest solution. Only solve for what is asked for.
Draw the shear and bending moment diagram of the given system. Flexural rigidity is equal to EI. Use Method of consistent deformation.
For the given girders of the frame shown which carries a uniform load of 12 kN/m along span GH and HI and a uniform load of 36.2 kN/m along span DE and EF. Dimensions are given as follows: A = 3.7 meters B = 5.1 meters C = 7.4 meters Using the approximation for building frames under vertical loads. G [A] [A] [B] [C] Compute the value of the absolute moment at reaction B. (kN-m) « Previous Quiz save
Find the moment of resistance of the section. The permissible stresses are 10 N/mm2 in tension and 16 N/mm2 in compression. use 3 decimals, draw Free body diagram
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given structure with P= 952 lb. Во 12 ft The force in member AB is The force in mémber BC is P Using the method of joints, determine the force in each member of the truss shown. State whether each member is in tension (7) or compression (C). The force in member AC is 3.75 ft 9 ft lb (Click to select) ✓ lb (Click to select) V lb (Click to select) ✓
Problem 2: Determine the forces in all diagonal and horizontal members of the truss shown below using the method of sections. Determine the force in all vertical members using the method of joints. Hint, the structure is symmetric. The distributed load is transferred to the truss from the roof purlins. State whether the members are tension or compression. Summarize your results on a sketch of the truss. 2.5 k/ft H M K 12 ft A G B C D F 6 @ 12 ft = 72 ft
For the truss shown below, P = 9.1 kips, a = 9 ft, and b = 7 ft. Determine the force in member 1 (tension is positive). Give the answer to one decimal place. Type your answer..