8. A belt conveyor is used to deliver a fluid to a reservoir, see the figure. The depth of the fluid film on the belt is such that the velocity on the free liquid surface of the film is zero. By considering only the work done by the belt on the fluid in shear, find the efficiency of this device. e of Engin epart

8. A belt conveyor is used to deliver a fluid to a reservoir, see the figure. The depth of the fluid film on the belt is such that the velocity on the free liquid surface of the film is zero. By considering only the work done by the belt on the fluid in shear, find the efficiency of this device. e of Engin epart

Name: 8. A belt conveyor is used to deliver a fluid to areservoir, see the
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 8. A belt conveyor is used to deliver a fluid to areservoir, see the figure. The depth of thefluid film on the belt is such that the velocityon the free liquid surface of the film is zero.By considering only the work done by thebelt on the fluid in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the minimum time to withdraw 50 L of kerosene from the cylindrical tank with 147.43 cm long to the can with 20 cm height put in the ground if we use a siphon hose with diameter is 16 mm. take kerosene density 810 kg/m^3?
The load carrying crane shown in the figurethe drum with its rope wound with one hydromotorare driven. Object A is slanted as the rope hugsIt moves up and down over the sled.The diameter of the drum on which the rope is wound is 300 mm.All hydraulic system until hydromotor30% of pressure losses in the components (efficiency 0.7)It will be taken. Thread of hydraulic gear pump in one round0.8 lt of oil dispensed from the cavitiesSince it isa. Calculate the flow of the pump (lt / min)b. Find the working pressure of the pump (bar)Load speed v = 0.6 m / sTensile force on the rope T = 10,000 NIt will be taken.
AT. 2] a water pump is to be used in a water supply system as shown in the figure. The pressure at point 1 is 70 kPaa and the pressure at point 2 is 101 kPaa. The velocity in the 60-mm pipe is 2 m/s. Find the pump power. Neglect friction, and assume no change of internal energy of the water and no heat transfer between point 1 and 2. Take the density of water at standard condition. 2 m2 10 m Pump
a water pump is to be used in a water supply system as shown in the figure. The pressure at point 1 is 70 kPaa and the pressure at point 2 is 101 kPaa. The velocity in the 60-mm pipe is 2 m/s. Find the pump power. Neglect friction, and assume no change of internal energy of the water and no heat transfer between point 1 and 2. Take the density of water at standard condition.
Water from a reservoir is pumped over a hill through a pipe 3 ft. in diameter, and a pressure of 35 psi is maintained at the summit, where the pipe is 300 ft above the reservoir. The quantity pumped is 55 cfs, and by reason of friction in the pump pipe there is 10 ft of head loss between the reservoir and the summit. What amount of energy must be furnished the water by the pump in kilowatts?
Phy
For the tank in the figure, calculate the volumetric flow of water, which comes out through a pipe, the tank is sealed and there is a pressure of 140 KPa above the water, the depth is h1=2.5M
A circular pipe of I.D. 4 m is bifurcated into two pipes of I.D. 2 m each. If the average velocity of water flowing through the main pipe is 5 m/s, then the average velocity through the bifurcated pipe is
The cylindrical in the figure is filled with 31.4 m3 of water at t = 0. The radius of the tank is 1 m and its height is 10 m. There is an outlet line with a radius of 0.2 m at the bottom of the tank. a. What is the time required for half of the water in the tank to drain after the outlet line is opened?b. The flow velocity of water from the bottom of a water tank is related to the height of the water in the tank, and this relation is v² = 2gh where v: (m / s) linear flow velocity, g: gravitational acceleration (10 m / s2) and h: (m) height.
For the system shown in figure, find the time required to fill the cylindrical tank (D-60cm) if. V-3m/s, Di-2cm, V-5m/s, D,-6cm, and V3-7.2m/s, Dy-5cm. h=1.2m
On a trip to the beach (Patm 1 atm or 101.3 kPa), a car runs out of gasoline and it is necessary to siphon gasoline from a Good Samaritan's car. The siphon is a hose with a small diameter and to start the action it is necessary to insert one end into the tank full of gasoline, fill the hose with it through suction and then put the other end in a can that is placed under the tank level. The difference in pressure between point 1 (on the free surface of the gasoline in the tank) and point 2 (at the outlet of the tube) causes the liquid to flow from the highest elevation to the lowest. In this case, point 2 is located 0.75 m below point 1, and point 3 is 2 m above 1. The siphon diameter is 4 mm and friction losses in it must be ruled out. Determine: a) theminimum time to bring 4 L of gasoline from the tank to the can and b) the pressure at point 3. The density of the gasoline is 750 kg / m3.