8 mm 76 mm 50 mm 500 mm

Q: Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 14  ×   1214⁢  ×   12 -in.…

A:

Q: Question 1 B 900 mm 80 mm -40 mm T A The magnesium tube is bonded to the steel rod. Part A If the…

A: Shear stress of magnesium = 45 MPaShear stress of steel = 75 MPaModulus of rigidity magnesium = 18 ×…

Q: A torque of magnitude T = 12 kN-m is applied to the end of a tank containing compressed air under a…

A: GivenT=12kN.mP=8MPat=12mmI.D=Di=180mmri=90mm=0.09mro=90+12=102 mm=0.102mSolutionPolar moment of…

Q: PROBLEM 3.56 Two solid steel shafts are fitted with flanges which are then connected by fitted bolts…

A: ** Make BC as CD

Q: 2.17 In using this leg curl machine the exertion of the legs results in a torque M 120 lb-ft on the…

A:

Q: The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with ry= 22…

A:

Q: orce of P₂ = 610 N is exerted on control arm BC, which is securely attached to the solid 39 mm…

A:

Q: The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing…

A: Given Data: The diameter of the rod AB is: dAB= 60 mm The outer diameter of the pipe CD is: dCD=90…

Q: 3. A shaft composed of segments AC, CD and DB is fastened to rigid walls and loaded as shown. For…

A: Solution:(a) Free Body Diagram (FBD) of the Composite ShaftFirst, let's understand the torques at…

Q: The solid circular shaft shown is made of a steel that is assumed to be elastoplastic with ry= 145…

A: The below information is given: τY = 145 MPa = 145 × 106 Pa c = 32 mm = 0.032 m Plastic zone tp =…

Q: The solid shaft (loaded as shown) is made of material that has an allowable shear stress of 10 MPa.…

A: The solid shaft (loaded as shown) is made of material that has an allowable shear stress of 10 MPa =…

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side…

A:

Q: d₁ = 38 mm d₂

A:

Q: The bell-crank mechanism shown is in equilibrium for an applied load of F₁ = 10 kN applied at A.…

A: The force applied, F₁ = 10 kNThe dimensions, a = 300 mm, b = 110 mm, c = 80 mm, and θ = 70ᵒThe…

Q: The two shaft

A: Design of shaft is important process in any mechanical system. Design of shaft is determined by…

Q: (2) A 200-mm-diameter pulley is prevented from rotating relative to 60-mm-diameter shaft by a 70-mm-…

A: Given:D=200 mmd=60 mmT=2.2 KN.mζallow=60 MPal=70 mm

Q: A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm…

A: The angle of rotation: The angle at which the fixed end rotates with respect to the free end is…

Q: A 2.5-in.-diameter solid aluminum post is subjected to a horizontal force of V = 4.70 kips, a…

A:

Q: Problem 8-12 A bar of rectangular cross-section, with a width of 60 mm and a thickness of 40 mm, is…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.