8- In lab tests on a 9.25 cm cube of a certain material, a force of 1375 N directed at 8.5° to the cube, as shown in the figure, causes the cube to deform through an angle of 1.35°. What is the shear modulus of the material? Page 6 of 6 9.25 cm 9.25 cm 8.50⁰ 1375 N 1375 N 8.50⁰ 4658 Ream

Q: A 463-N object is hung from the end of a wire of cross-sectional area 0.03 cm-. The wire stretches…

A:

Q: 3 a P M The scheme of supporting of the absolutely rigid body is shown in the picture. Define the…

A: Answer..

Q: Consider a copper wire with cross-sectional area 4 mm?. The Young's modulus for copper is 1.1 × 1011…

A:

Q: Q2 The structure shown in the following figure is made up of three blocks. No pin or other…

A:

Q: QUESTION 16 The T-beam is made of a nylon. The allowable stress is 24 MPa in tension and 30 MPa in…

A: The area of the top section will be, A1=80×30 ⇒A1=2400 mm2 And the area of the bottom section will…

Q: H = 8 cm L = 4 cm α = 50° t = 5 mm The strain value of the structure in the same direction as a…

A: Write the given values of this problem. H=8 cmL=4 cmα=50T=5 mm∈x=0.26 mm/mm

Q: 56 : The lower surface of metal cube, having each side of length 10 cm, is kept fixed and tangential…

A: Given: L=0.1m, ∆L=10-4m, η=8.4×1010N/m2   The shearing stress is defined by :  Shearing…

Q: empt in Progress When subjected to a force of compression, the length of a bone (compression Young's…

A: Given  Compression young modulus ,Yc = 9.4×109 N/m2  Tensile young modulus, Yt =1.6×1010 N/m2…

Q: Is thrée times larger than in steel shaft. QI1) For the section shown aside, if the bending stress…

A:

Q: 2. The area of the upper face of a rectangular block is 0.5m x 0.5 m and the lower face is fixed.…

A: Given: The area of the upper surface is A=0.5 m×0.5 m=0.25 m2 The height of the block is h=1…

Q: 37. .. BIO Spiderweb An orb weaver spider with a mass of 0.26 g hangs vertically by one of its…

A: Young's modulus:The Young's modulus of a material can be defined as the ratio of the tensile stress…

Q: 0.3 m /TM 10 kg 0.3 m /TM 5 kg

A: Given data m1=5 kgm2=10 kgA=0.05 m2Y=1.1×1011 N/m2 When a weight is suspended through a wire a…

Q: Based on the stress-strain diagram below, what is the approximate tensile stress? Stress v. Strain…

A: Tensile stress is the Force applied per unit cross sectional area of the material, which causes the…

Q: D 14 mm 300 mm| E B - 300 mm 3 mm 3 mm

A: Concept used: Strain is the ratio change in length (increase or decrease) to original length. The…

Q: EXample 2: the ankle joint therefore pushes upward on the bottom of the tibia with the force of 2800…

A: Given : R1=1.3 cmR2=2.5 cm

Q: What is the proportional limit? O None of these answers O 37,540 psi O 30,000 psi

A: Proportional limit is the the maximum stress for which graph is linear 40,000 psi

Q: Determine the maximum shear stress in the d-mm-diameter shaft. The shaft is fixed to support A but…

A: In this question answer is given below. It is helpful for you ?

Q: A violin string has a radius of 4.1 x 104m. During tuning, 32.5 cm of the string is placed under a…

A: Given Initial lenth of string is 32.5 cm Elongation of lenth is 0.93 cm Assume elongation in elastic…

Q: 1. A cubic-shaped elastic block with side length L = 50 cm is fixed to the floor. An external force…

A: To solve this problem, we'll approach each part step by step.Part (a) Determine the angle ϕThe angle…

Q: An aluminium (p = 2.7g/cm³) wire is suspended from the ceiling and hangs vertically. How long must…

A: Given that :Density of aluminium wire, ρ=2.7g/cm3Stress at upper end, σt= 8×107 N/m2Here we need to…

Q: Q4) A force of magnitude F = 62 × 10° N is applied perpendicularly to the steel rod of radius 9.5 mm…

A: Given data The magnitude of the force is F = 62 x 103 N The rod's radius is r = 9.5 mm. The length…

Q: A 1.8 x 10-3-kg house spider is hanging vertically by a thread that has a Young's modulus of 4.0 x…

A:

Q: Question 12 The shear modulus of aluminum is 2.40×10¹0 N/m². An aluminum nail of radius 7.49x10 m…

A:

Q: Many caterpillars construct cocoons from silk, one of the strongest naturally occurring materials…

A: We have L= 8 m  ∆L= 1.02 cm = 0.0102 m  m = 87 kg  Y = 4 ×109 N/m2  Diameter D = 2 × 10-6 m  Radius…

Q: Problems - Stress, Strain, and Young's Modulus P10-5. Zartan's vine, initially 6 m long, has a…

A: Given, Initially length of the vine, L=6m The Young's modulus, Y=0.1GN/m2Y=0.1×109N/m2 Stress,…

Q: A spider of mass 6.6 x 10-4 kg hangs from a 71.2 cm long thread whose diameter is 2.0 x 10-3 mm.…

A:

Q: Question 2 Calculate the torque in each section and the maximum shear stress in the shaft EH (Figure…

A: Torsion equation of shaft, TJ=τR Where J is polar inertia. τ=Td2πd432τ=16Tπd3   For EF, d=23×10-3m…

Q: A 557-N force is applied to stretch a cable, 66-m long and has a cross-sectional area of 2.8 mm^2.…

A:

Q: 1 m wire has a cross sectional area 10-4 m2. The wire is stretched by a load of 50 kg causing it to…

A:

Q: A man with a mass of 68.3 kg stands on one foot. His femur has a cross-sectional area of 8.00 cm2…

A: GivenM= 68.3 kgA =8.00 cm2 =8.00 ×10-4 m2uncompressed length (L) = 50.4 cm = 50.4 × 10-2 mYoung's…

Q: An Aluminum cable of length 2.5 m has 15,000 N tensile force acting on it, if the wire is only…

A: Given data:  Original Length (L) = 2.5 m Tensile forcey(F) = 15,000 N Stretch in the spring (ΔL) =…

Q: Question 28 -4 The shear modulus of aluminum is 2.40x10¹0 N/m².. An aluminum nail of radius 7.51x10…

A:

Q: The short cylindrical block having an original diameter of 1 cm and a length of 5 cm, placed in the…

A: Given Axial load  F= 3000 N Diameter D = 1 cm = 10 mm Length L     = 5 cm = 50 mm Poisson's Ratio of…

Q: A television set rests on four rubber pads, each one having a height of 1.0 cm and a radius of 0.60…

A: The answer is below