Answered: a) Determine the average normal (o) and… | bartleby

Related questions

Question

Q2- A biological tissue underwent tensile tests, subjected to the axial load P.
a) Determine the average normal (ơ) and average shear stresses (t) acting over area section
shown below(A'), which is oriented at angle 0 from the horizontal, as a function of 0 and
vertical cross section A.
b) Determine angle 0 where o=3 t.
(24 points)
A'=A/sin0
P
01
A
(Results: o =- (sine)²,t = - sin0 cose,0 = 71.56°)
%3D
A
А

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

If the long term permissible load capacity for three nails in double shear in C22 timber is given as 1660.5 N using 3.35mm x 90mm long round wire. What is the slip per nail in mm? (Answer in 2 decimal places) Answer:
show complete solution
An axial load Pis applied to the rectangular bar shown. The cross-sectional area of the bar is 216 mm?. Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB if the bar is subjected to an axial load of P = 77 kN. Assume a = 61°. B Answers: The normal stress o = i MPа. The shear stresS T = MPa.
A fishing rope of length (74+ 50) m has the diameter (74 + 5) mm. When a weight of (74 +200) N is hung on the rope, the extension is (74 + 50) mm. Calculate,i. cross-sectional area of the fishing ropeii. strain
The rubber blocks shown are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 336 N causes the upper frame to be deflected downward by 5.5 mm. Determine the shear modulus Gof the rubber blocks. Assume a = 10 mm, b = 22 mm, and c = 27 mm. Double U anti-vibration shear mount b P Rubber block dimensions Shear deformation of blocks Answer: Shear Modulus G = i MPa.
1. A steel beam is placed vertically in the basement of a building to keep the floor above from sagging. The load on the beam is 6.0*104 N, the length of the beam is 2.7 m, and the cross-sectional area of the beam is 7.3*10-3 m2. Find the vertical compression of the beam. The young’s modulus of steel is 200 *109 Pa.
28.
Member BC has a square cross section. The diameter of the pins at A and B are 3 cm and 2 cm respectively. If the allowable normal stress for member BC is allow = 25 MPa and the allowable shear stress for the pins iS Tallow = 12 MPa, calculate the maximum force intensity w (in N/m). 4 cm В 50° 3 m A W
2. The pin at A has a diameter of 0.25 in. If it is subjected to double shear, determine the average shear stress in the pin. -2 ft +2 t- 3 ft 600 Ib B
6. A steel beam is placed vertically in the basement of a building to keep the floor above from sagging. The load on the beam is 5.8*104 N, the length of the beam is 2.6 m, and the cross-sectional area of the beam is 7.1*10-3 m2. Find the vertical compression of the beam if the Young's modulus of steel is 2.00*1011 N/m2
An upright beam supports a load of 3,000 N and 2,500 cm long. The beam is compressed 200 mm by aload. Young’s modulus of the beam is 1.0x10 11 N/m 2. Calculate cross-section area of the beam.