8 F-5 Fighter airplane has q caing area of 170 ft?. The wing gener ateo a lift of 18000 16. For 9 Blight Velocity of 250 mph at standard sea-level conditions. The dynamic pres ore 90 2. - foo Voo = 159.8 1bf/f42 Explain how to get the dynamic presure

Q: In the drawing operation, technological property weldability is an important parameter. Select one:…

A: Drawing: It is a process in which uses tensile forces is used to stretch metal.

Q: The example for forming process is ___________. a. Tempering b. Drawing c. Gas welding d. Die…

A: The example of forming process is drawing in which material goes under plastic deformation.

Q: Name 2 types of bending?

A: Bending is a type of forming process in which the required object maybe a rod, tube or sheet metal…

Q: Write the application and advantages of Honing Process?

A: Honing Process: It is a finishing process of machined surfaces. It is used to finish internal…

Q: what would be the order of operations to make this part in the least amount of time and how would…

A: The order of operations to make this part in the least amount of time and how would you hold the…

Q: 5) In soft soldering a low melting range alloy of tin and lead is used as filler metal. Select one:…

A: It is true

Q: pes o

A: GIVEN: Explain different types of fits?

Q: Identify the forming process in which the rectangular shape of the cross section is reduced into…

A:

Q: Sheet Forming Processes; V-Bending of Sheets is more expensive than Edge Bending. (T or F) In Metal…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Q\Why the metals family could be strengthening

A: Both crystalline and amorphous materials may have their yield strength, ductility, and toughness…

Q: In the 3% error, why is the design acceptable?

A: Given: There are 3% error in the design. And by this error the developed power reduced from 0.556 MW…

Q: What is impact loading?

A: Impact loading is a type of loading whose period of action is very less. Generally, when the time of…

Q: Define build-up and draw down test??

A: Build-up test The build-up test is mostly performed in oil industries for calculating the flow rate…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Instruction: : Explain briefly the hardening pr0cess Of a metal.

A: given; explain briefly the hardening process of a metal.

Q: Propose any improvements if there are any in breaking system

A: The various improvements that can be made in a breaking system are given below. 1. Increasing disc…

Q: need answer within 20 minutes please please with my best wishes

A: Superfinishing is different from honing in a way that:- In honing the small removable of material…

Q: Which of the following is an example for surface treatment process. a. Annealing b. Tempering c.…

A: Annealing is the heat treatment process that is generally used to increase the ductility property of…

Q: Why may ultimate strength be greater than rupture strength?

A: The given problem is for ductile materials because for brittle materials there is no plastic…

Q: What are the disadvantages of mock up method?

A: A mock-up is a model or a prototype having a different or similar scale with the actual product. A…

Q: 32 - (CLO-1) What is cold shut defect? a) Two portions of metal flow together but there is lack of…

A: Cold shut is a casting defect

Q: Expain about Poisson's ratio?

A: Poisson's ratio: "The ratio of lateral strain to the longitudinal strain is called Poisson's ratio."…

Q: 9. The top view shows a bend radius of the thin metal. Would a bend radius of 1/8" meet the…

A: If the bend radius lies with in the given range then it will meet the requirements. 18"=0.125" The…

Q: Which one of the following material has the sheet metal applications O a. Mild steel O b. Cast iron…

A: Sheet metal is metal forming process which is used for forming into sheets

Q: Why should stress not exceed the material by design?

A: Every component is designed based on working stress which will acts on the component during its…

Q: enumerate the 4 plate forming process and where it can be applied

A: given; enumerate the 4 plate forming process and where it can be applied.

Q: Which one of the following differs from the casting processes in which the die halves are closed…

A:

Q: How is the Force Method of Analysis applied?

A: The force method of analysis is a method that is used to determine the unknown forces form the…

Q: How were the areas for part 2 found?

A: Given Data and to find: How the areas are calculated?

Q: Anisotropy in a metal O increases residual stresses. O properties vary with direction. increase the…

A: 1) Anisotropy- it is the property of material in which the meterial properties changes with…

Q: Which of the following is a suitable process for creating a hollow 3D shaped component?

A: Option a is correct.

Q: Why materials like glass, cork and cracked stainless steel mixing device are not suitable to be used…

A: Stainless steel has a crystalline nature While glass and cork are amorphous solids.

Q: Find the best match for the individual statement given below: Prompts Submitted Answers Fatigue…

A: Let us discuss about above statements and their matches.

Q: what other manufacturing process steps may be required for the machined plate prior to use?

A: We have given a machined plate and we want to use it in another task. So for that purpose we have to…

Q: 9) Tubes can be produced by ___________ process. a. Extrusion. b. Drawing. c. Milling. d. Forging.

A: Option a is the correct option.

Q: Hollow shape parts are made __________ process. a. Cold rolling b. Wire drawing c. Deep drawing d.…

A: Rolling process are use to produce the symmetrical objects. Wire drawing process is used to produce…

Q: 8) __________ notched specimens are used for Charpy impact test. Select one: V U & V U Key hole

A: V notched specimens are used for charpy impact test

Q: 38- A blanking operation is to be performed on 8.0 mm thick soft cold rolled steel. The part is…

A:

Q: Sketch and explain any four Shaper operations?

A: The four shaper operations are, Horizontal cutting: It's one of the most popular operations on a…

Q: Which of the following metal forming processes is best suitable for making the cup shaped products?…

A: Rolling is generally used to reduce the thickness of a metal sheet. Forging is shaping of a material…

Q: Choose forming and generating operation 2 po Work Work Threa dsad dsa Generated surface Work Work…

A: This is taper turning

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.