8-7. A steel plate with holes cut in it is shown below. The plate has a thickness of t=6.35mm and densityof 8000 g. Determine its centroid location using the bottom left corner as the origin.mDo M7.46 cm10.00 cmFigure 8-311.28 cm4.91 cm8.72 cm5.83 cm[2.81 cm

The thickness of the section, t = 6.35 mmDensity = 8000 kg/m3To determine the coordinates of the…

8-7. A steel plate with holes cut in it is shown below. The plate has a thickness of t=6.35mm and density of 8000 kg. Determine its centroid location using the bottom left corner as the origin. m Do X 7.46 cm 1.28 cm 4.91 cm 8.72 cm 5.83 cm [2.81 cm

8-7. A steel plate with holes cut in it is shown below. The plate has a thickness of t=6.35mm and density of 8000 kg. Determine its centroid location using the bottom left corner as the origin. m Do X 7.46 cm 1.28 cm 4.91 cm 8.72 cm 5.83 cm [2.81 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitude and direction of the resultant of the two forces acting on the plate shown below.
Calculate the x-, y-, and z-coordinates of the mass center of the bracket formed from the steel plate of uniform thickness. 140 235 mm mm 140 mm 300 mm 155 mm Answers: mm mm i mm
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 415 mm?, 636 mm² , and 253 mm² respectively.Determine the change in length (in mm) of the bar if P = 28084 N.The moduli of elasticity are 83.77 GPa for bronze ,71.95 GPafor aluminum , and 204.98 GPa for steel. Round off the final answer to four decimal places. Bronze Aluminum Steel 2P ЗР P. 4P 0.6 m →k 1.0 m 0.8 m Add your answer
5) In the section of the figure below, 6 rebars 36 are used as tensile steel and 4 rebars number 20 are used as compressive steels. Assuming d' is 60 mm and fy is 400 MPa, calculate the anchor of the ultimate cross-sectional strength. 800mm 150mm 750mm 700mm O O 300mm (If there is a lack of problem information for the numerical solution section, make a logical assumption and write it down) The answer must be typed, avoid handwriting. The answer should be short and completely correct, l give a negative score to the answer that I feel is wrong; so please be careful, thank you.
The bar composed of aluminum was sustained by the 14 mm2 cross-sectional area of the pin-connected rod CB. When the bar is vertically deflected at D, calculate the vertical deflection of the bar when distributed load is applied Given: E = 68.9 x 10^9 Pa
The figure as shown below is a rigid bar (ABCD) which was supported thru pin at B. Two bars was also connected, Bar CE and Bar DF with corresponding cross-sectional area and Modulus of Elasticity. If P is equivalent to SN kN, the diameter at pin B is Blank 1 mm. SN=78
Can you show how 184 appear? This is the problem: The beam shown in figure is 5 inches wide and 10 inches deep. What is the maximum bending stress?
Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces of uniform thin plate which are welded together. 560 mm 240 480 mm mm 85 mm 185 mm 320 mm The tolerance is + 1 in the 3rd significant digit. = i mm i mm i mm
Statics Civil engineering The plate is suspended how using three cables applying the forces shown. Express each force as a cartesian vector. Use 3 digits after the comma.
1 Determine the coordinates of the center of mass of the bracket, which is made from a plate of uniform thickness. 45 mm 95 mm Answers: 70 mm 120 mm (X,ZZ) = ( ) mm
The bolt in (Figure 1) is fixed to its support at C. Figure B in. A 6 in
I need the answer quickly