8-26. The lap joint is connected together using a 30 mmdiameter bolt. If the bolt is made from a material having ashear stress-strain diagram that is approximated as shown,determine the shear strain developed in the shear plane ofthe bolt when P - 340 kN.7 (MPa)525350(rad)0.0050.05

Calculate the load on the bolt. Here, Pbolt is the load on the bolt. Calculate the shear stress in…

Answered: 8-26. The lap joint is connected…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-71. The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is Tail 350 MPa. Use a factor of safety for shear of F.S. = 3 40 kN 40 KN 30 mm 80 KN 30 mm
The lap joint is connected together using a 30 mm diameter bolt. If the bolt is made from a material having a shear stress-strain diagram that is approximated as shown, determine the permanent shear strain in the shear plane of the bolt when the applied force P =750 kN is removed.
If P=5kN, determine the average shear stress in the pins A, B, and C. All pins are in double shear, and each as a diameter of 18 mm. P 0.5 m B 3P -1.5 m- 2 m 6P -1.5 m- P 0.5 m
The elastic portion of the tension stress–strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gage length of 2 in. and a diameter of 0.5 in. If the applied load is 10 kip, determine the new diameter of the specimen. The shear modulus is Gal = 3.811032 ksi.
The rectangular plate is subjected to the deformation shown by the dashed line. Assume a = 550 mm, Ax = 2.2 mm, and Ay = 1.4 mm. Determine the shear strains Yxy and Yxy at point A. Ay Ay Answers: Vxy= | i Ax Yxy= i eTextbook and Media Save for Later X urad urad Attempts: 0 of 5 used Submit Answer
مقاومة المواد
8-21. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. When the applied load on the specimen is 50 kN, the diameter is 12.67494 mm. Determine Poisson's ratio for the material. 8-22. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. If a load of P = 60 kN is applied to the specimen, determine its new diameter and length. Take v = 0.35. σ (MPa) 490 0.007 Probs. 8-21/22 € (mm/mm)
Draw Mohr’s circle for sx = sy = txy = 2 kPa. On the circle, label the axes and the principal stresses and their angles. Using three significant digits, determine the principal stresses and their angles, and the normal and shear stresses at q = 80 degree. The three gages from the strain rosette mounted on a steel shaft have the following readings: εa = 0.000316, εb = 0.000248, and εc = 0.000579. Determine the strain components: εx, εy, and Yxy.
Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. Originally the cable is unstretched. Part A AB= If a force is applied to the end B of the member and causes a normal strain in the cable of 0.00484 mm/mm, determine the displacement of point B. Express your answer to three significant figures and include appropriate units. μA Value - 600 mm. Units 800 mm
A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever is P = 395 N, determine the shear force applied to the shear key. 42 mm. ↓ Shear key O 10.90 KN O 18.31 KN O 9.70 KN O 14.25 KN O 13.17 kN 700 mm C Shear key detail
A plate is fastened to a fixed member by four 20-mm-diameter rivets arranged as shown in Fig. P-333. Compute the maximum and minimum shearing stress developed.
The five-bolt connection must support an applied load of P = 2600 Ib. If the average shear stress in the bolts must be limited to 27 ksi, determine the minimum bolt diameter that may be used for this connection. Answer:dmin = in.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

8-26. The lap joint is connected together using a 30 mm diameter bolt. If the bolt is made from a material having a shear stress-strain diagram that is approximated as shown, determine the shear strain developed in the shear plane of the bolt when P - 340 kN. 7 (MPa) 525 350 (rad) 0.005 0.05