7.4-17 A sign is supported by a pole of hollow circular cross section, as shown in the figure. The outer and inner diameters of the pole are 10.5 in. and 8.5 in., respectively. The pole is 42 ft high and weighs 4.0 k. The sign has dimensions 8 ft × 3 ft and weighs 500 lb. Note that its center of gravity is 53.25 in. from the axis of the pole. The wind pressure against the sign is 35 lb/ft². (a) Determine the stresses acting on a stress element at point A, which is on the outer surface of the pole at the "front" of the pole, that is, the part of the pole nearest to the viewer. (b) Determine the maximum tensile, compressive, and shear stresses at point A. -8 ft- Hilda's Office 3 ft -10.5 in:- 42 ft +8.5 in.- X|X A A Section X-X

7.4-17 A sign is supported by a pole of hollow circular cross section, as shown in the figure. The outer and inner diameters of the pole are 10.5 in. and 8.5 in., respectively. The pole is 42 ft high and weighs 4.0 k. The sign has dimensions 8 ft × 3 ft and weighs 500 lb. Note that its center of gravity is 53.25 in. from the axis of the pole. The wind pressure against the sign is 35 lb/ft². (a) Determine the stresses acting on a stress element at point A, which is on the outer surface of the pole at the "front" of the pole, that is, the part of the pole nearest to the viewer. (b) Determine the maximum tensile, compressive, and shear stresses at point A. -8 ft- Hilda's Office 3 ft -10.5 in:- 42 ft +8.5 in.- X|X A A Section X-X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need to draw a free body diagram and the solution L=88m
EXAMPLE: II. 2 ft Show the V-M diagram using Area Method of the following beam: R₂ 200 lb/ft 4 ft - Hinge 2 ft
Two street lights are mounted as shown in the figure one at A and the other at C. The member AD is able to freely rotate about D. Member BE is a steel cable. B. EACH street light has a mass of 5 kg, AB=20cm, BC=20cm, CD=10cm, DE=17.32cm. Assume gravity is 9.81 N/kg. h=4cm Draw the shear force profile (a) between point A and D. On the diagram, clear indicate the values on the diagram. (b) member just to the right of point B. Calculate the maximum bending shear stress. At what distance from the bottom does it occur? Consider a cross-section of the (c) distance from the bottom does the minimum bending shear stress occur? What is its value? For the same cross-section, at what
Consider the pendulum shown in the figure. Calculate: y r," А A' 0.5h" B' h" t" r2 C C' COLLAPSE IMAGES li = 0.2 in r2 = 1.2 in h = 4 in t = 0.1 in The moment of inertia about the y axis. in4 ENTER The moment of inertia about the x axis. in4 ENTER The moment of inertia about the AA' axis. int ΕΝTER
Solve fast with suitable diagram
In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D connected to F. Determine the following give that Force F is equal to 690.86 N. Note: Express your answer in terms of the units. Observe 3 decimal places. 1.) Determine x-component of vector DF. 2.) Determine the y-component of Vector DF 3.) Determine the z-component of Vector DF. 4.) Determine the moment experienced by the system assuming that there is no wire support.
A cylinder has a conical cavity and is topped by a hemispherical cylinder, such as as indicated in the figure. a) Locate the centroid of the composite volume if R = 200 mm and h = 250 mm. b) Locate the center of mass of the composite volume if the cylinder is made of brass (ρ = 8750 kg / mᶟ) and the finish is made of aluminum (ρ = 2770 kg / mᶟ)
Need help please Include all units and steps
6 m 40 kN -8 m- -12 m- Figure Q3(a)
The plate shown in Figure is supported by a roller and a cable in the x-direction at A, a ball-and-socket joint at B, and a roller at C. A force F = 8.1 kN is applied at the centroid of the plate parallel to the yz-plane and making an angle of θ = 40 ∘ with the xy-plane. The sides AB and BC of the plate have length L = 1.5 m . 1) What is the reaction force in the y-direction at point B? Let a positive force act in the positive y-direction? 2) What is the reaction force in the z-direction at point C? 3) What is the reaction force in the z-direction at point A?
(c) The cross section of a quarter circular concrete block XYZof width 1.8m is shown in Figure 3. The specific weight of the concrete mix is 24 kN/m3. The hinge is along XX. Calculate the vertical force R at Y to hold the gate in this position. K Fixed slab 1.2 m Y W Fy 1.3 m FĦ D B Figure 3