7.35 An npn BJT with grounded emitter is operated with VBg = 0.700 V, at which the collector current is 1 mA. A 2- k2 resistor connects the collector to a +5-V supply. What is the resulting collector voltage V? Now, if a signal applied to the base raises vBE to 705 mV, find the resulting total collector current ic and total collector voltage ve using the exponential ic-vBE relationship. For this situation, what are vhe and v.? Calculate the voltage gain v/vbe- Compare with the value obtained using the small-signal approximation, that is, -gmRc.

7.35 An npn BJT with grounded emitter is operated with VBg = 0.700 V, at which the collector current is 1 mA. A 2- k2 resistor connects the collector to a +5-V supply. What is the resulting collector voltage V? Now, if a signal applied to the base raises vBE to 705 mV, find the resulting total collector current ic and total collector voltage ve using the exponential ic-vBE relationship. For this situation, what are vhe and v.? Calculate the voltage gain v/vbe- Compare with the value obtained using the small-signal approximation, that is, -gmRc.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the figure, A characteristics curve is shown for the MOSFET. Determine the following outcome and parameters using the values given in the characteristics: i) Find the Ip for the VGs = 4V, where IGs(ON) = 4.5mA ii) Find the transconductence of MOSFET; where, MOSFET having the bias voltage VGs = 4V, and 6V. %3D A (mA) A5 (mA) 10 10 VGs=+8 V 9. 7 .7 VGs =+7 V 6 5 Vas=+6 V 4 VGs =+5 V 2 VGs =+4 V Vas =+3 V 1 3 4. 5 8 Vas 10 15 20 25 Vos Vas = VT=2 V a co
Most of the emitter-injected electrons pass through the base region and into the collector region because: a) The positive collector-base voltage attracts the free electrons in the p-type base over to the collector side before they can recombine with holes in the base. b) Only a few holes are available for recombination in the base. c) Holes are greater than electrons d) The negative collector-base voltage attracts the free electrons in the p-type base over to the collector side before they can recombine with holes in the base.
Bipolar junction transistors (BJTS) are considered “normally-off" devices, because their natural state with no signal applied to the base is no . .between emitter and collector, like an open switch. *
Please answer 1 and 2 in step by step solution
A silicon (Si) npn bipolar transistor is doped with impurity concentrations of 10° cm, 10" cm, and 106 cm in the emitter, base and collector, respectively. The lengths of the emitter and collector length are 1 um and the base width is 500 nm. The device is operating at room temperature. (3) Determine the base current density in the transistor if the base emitter voltage VBs is forward biased with 0.5 V. Assume the base and emitter lengths are shorter than the diffusion length. (4) Explain why current gain is higher in npn transistors than in pnp transistors. (5) Sketch forward active lc vs. VE characteristics of the npn transistor as Vae increases with equal increments of voltage (e.g. 400 mv, 450 mv, 500 mv and 550 mV). You do not need to calculate values for collector current.
In r-parameter model the emitter resistance is smaller than the base resistance yet wekeep it and remove the replace the base resistance by a short circuit, explain why?
In single transistor amplifier design, it is observed that the voltage gain will always decrease as the load resistance increases. True False The saturation region of MOSFET indicates that the drain current no longer depends on the source-drain voltage while the saturation region of BJT indicates that the collector current no longer depends on the collector-emitter voltage. True False A bipolar junction transistor can be connected to behave like a diode while a field effect transistor can not be connected to behave like a diode. True False A voltage follower circuit is usually designed to have the power gain slightly less than 1 with any passive load. True False A clipper circuit regulates DC voltage input while a clamp circuit regulates AC voltage input. True False
Hey, can you please make sure this question is solved correctly and step by step solution to the way to approach and how it's done please. I want to learn how to do this type of problem. Figure 2 shows a more realistic BJT cross-section.Collector virtually surrounds entire emitter region. This makes it difficult forelectrons injected into base to escape collection. Device is not symmetrical.Can emitter and collector be interchanged?Is this BJT a uni-directional device?Explain.
1) Write the 2 conditions for a diode to conduct 2)Find the value of the IC current in the NPN transistor amplifier circuit in the figure when IB is 1mA." (Beta=100) 3)If VCE is given as 0.5V when the transistor is in saturation and the voltage drop across the LED is 1.5V, what is the value of the RC resistor that provides the IC current?lf (Beta=100) 4)If the LED is shining brightly at a current of 12 mA, how many parallel LEDs can we operate? answer the questions(dont use chatgpt) Vcc= 12V Rc=? LED MVC IB Ic 40 E
BJT question
Can someone explain this problem to me. I don't know how to get to the answer that is given.