I need help with this worksheet Threads worksheet 9-4. Is not graded. M30Ø25Ø32h60.8Ø30-M20 T 18-Ø19.5M2440НЕХ.3-25Ø1510M18 X 1.5 V 12122590-MATERIAL: 303 STAINLESSFINISH: NONENAME: STEMNO.: 9-3 Add theCorrect AnswerCalculations7.Pitch8.Length of threads11.Pitch16.Pitch

Standard designation for Metric thread

Answered: 7. Pitch 8. Length of threads 11. Pitch…

Engineering

Mechanical Engineering

7. Pitch 8. Length of threads 11. Pitch 16. Pitch

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How would you solve this
Can I get the Top, Side and views. Using free-hand drawing of this coupling pieces..
Draw the Apple logo in AutoCAD
Tire manufacturers recommend that you check your tire pressure monthly to avoid unnecessary tire wear and enhance safety. This is best done when the tires are cold meaning; the car has not been driven for at least 2 hours. Since you leave for work before the sun comes up you decide to inflate your tires to the recommended pressure right after you get home from work in the afternoon when the tires are still warm. What would you find if you rechecked your tire pressure after the tires have cooled down? A.Tire pressure has decreased because there is a decrease in kinetic energy of themolecules resulting in more collisions with the inside walls of the tire thusincreasing the pressure inside the tire. B.Tire pressure has increased because there is a decrease in kinetic energy of the molecules resulting in fewer collisions with the inside walls of the tire thus decreasing the pressure inside the tire. C.Tire pressure has increased because there is an increase in kinetic energy of the…
Hello, please answer as soon as possible. Choose from the given choices/options below the question. Show complete solution. Thank you for your help. I’ll rate you with like/upvote.
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE = 65 in3 Cyl. A DR = 62 in3 Cyl. B DE = 44 in3 Cyl. B DR = 41 in3
Part 2 Set up a spreadsheet solution to this problem. This will require that you derive one formula to express the relationship between the friction coefficient, the spring constant, and the spring compression; and a second formula to find the cost of using different slide and spring types. Set up your spreadsheet as shown below. You can fill in the "Acceptable?" column manually, rather than using a formula. Turn in a copy of your spreadsheet/Matlab work (solve for $) Friction Spring Constant Spring Compression M k 0.1 0.1 0.1 0.2 0.2 0.2 50 100 150 50 100 150 4 Part 3 Your boss has decided to look at a second option. The spring mechanism will be replaced by a drop box. After leaving the slide, the blocks will travel 5 horizontal feet through the air and pass through a hole into the drop box. Using the slide you selected above, determine how far below the slide (h) to place the hole in the drop box. Yo = 5.2017/5 BLADE 2 RAMPE SLIDE 8⁰ SLIDE Acceptable? (Yes or No) $' Cost 51 In DROP…
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…