7. Make a spread sheet blend template program to perform a blend gradation analysis for up to four stockpiles with the ability to produce automatically semilog or power 0.45 gradation charts. Use the table to demonstrate the template, and calculate the fineness modulus for the aggregate D. Aggregate Blend Percent (%) Sieve size (mm) 37.5 25 19 12.5 9.5 A 20 100 100 95 89 70 B 25 100 100 100 100 82 C 25 Percent Passing 100 100 100 100 100 D 30 100 100 100 100 100

7. Make a spread sheet blend template program to perform a blend gradation analysis for up to four stockpiles with the ability to produce automatically semilog or power 0.45 gradation charts. Use the table to demonstrate the template, and calculate the fineness modulus for the aggregate D. Aggregate Blend Percent (%) Sieve size (mm) 37.5 25 19 12.5 9.5 A 20 100 100 95 89 70 B 25 100 100 100 100 82 C 25 Percent Passing 100 100 100 100 100 D 30 100 100 100 100 100

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

You are given a result of the gradation test of aggregate, calculate and plot the gradation curve on the given semilog graph shee
4. From the given data shown in the table below, determine the effective specific gravity of aggregates. Round off to two decimal places.
10. A sample of coarse aggregate weighs 1072 g when oven- dried, 1091 g when saturated surface-dried, and 667.6 g when submerged. Calculate the bulk specific gravity, apparent specific gravity, and absorption.
Given for a set of aggregates: A=2030.9, B 2044.9 and C=1304.3 A = Oven dry weight B = SSD weight. C = Weight in water Find the Bulk Specific Gravity, Bulk SSD Specific Gravity, Apparent Specific Gravity and Absorption
Aggregates from three sources having the properties shown in the table below where blended at a ratio of 30:45:25 by weight. Determine the properties of the aggregate blend. (Please show me in direct solution)
help me find solutions for a,b,c,d,and e
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? " Sieve Size, 9.5 4.75 3.35 2.36 2.00 1.18 0.85 0.60 0.425 0.30 0.25 0.18 0.15 (No. 0.075 Pan mm (in) (3/8) (No. 4) (No. 6) (No. 8) (No. 10) (No. 16) (No. 20) (No. 30) (No. 40) (No. 50) (No. 60) (No. 80) 100) (No. 200)| Amount 25 59 75 86 115 136 169 192 225 198 173 112 90 33 12 Datained.
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve.b. Plot the percent finer in a semi-log gradation chart.c. What is the maximum aggregate size of the sample?d. What is the nominal maximum aggregate size of the sample?e. What is the fineness modulus? Is it in typical range?