7. Knowing that 0=40° and P=9 kN, determine (a) the smallest allowable diameter of the pin at B if the average shearing stress in the pin is not exceed 120 MPa, (b) the corresponding average bearing stress in the member AB at B, (c) the corresponding average bearing stress in each of the support brackets at B.

Q: Q1 The curved portion of the bar shown has an inner radius of 20 mm. Knowing that the allowable…

A: Given,

Q: Determine the value of Q so that the deformation at A is zero.

A: Given:E = 70 GPaP = 3.5 kNDiagram is givenTo find:Value of Q so that the deformation at A is zero

Q: The couple M is applied to a beam of the cross section shown in a plane forming an angle b with the…

A: Given:The couple is the angle is

Q: (a) A steel cylinder of 60 mm inner radius and 80 mm outer radius is subjected to an internal…

A: Note: As per the bartleby guidelines only three subpart will be solved at a time for remaining…

Q: 4.17. Determine the components of stress from the results obtained in (a) v=rsin 0, ve = 2r cos 0…

A: Sure, based on the image you sent, which is a circuit containing a battery, resistors, and an…

Q: 2.17 In using this leg curl machine the exertion of the legs results in a torque M 120 lb-ft on the…

A:

Q: The compressed air tank AB has a 250-mm outside diameter and a 10-mm wall thickness. The arm BC is…

A: Stress calculations:

Q: orce of P₂ = 610 N is exerted on control arm BC, which is securely attached to the solid 39 mm…

A:

Q: Link AB, of width b = 2 in. and thicknesst = ¼ in., is used to support the end of a horizontal beam.…

A: Handwriting.jpg

Q: A steel shaft of diameter 50 mm and length 1.2 m (E = 210 GPa and v = 0.3) is loaded with multiple…

A:

Q: 5 mm 20 mm 5 mm Steel core E = 200 GPa Brass shell E = 105 GPa 5 mm 20 mm .5 mm 250 mm

A:

Q: A vertical force P = 15 kip is applied at point C located on the axis of symmetry of the…

A: (a) Draw the cross-section for the figure and show the neutral axis for the section. Here,  is the…

Q: ! Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown.…

A:

Q: b. A draw bar between a tractor and a trailer is made from a length of steel with a rectangular…

A: Given Data

Q: Why is the net area for AB (0.045-0.0102) * (0.012) ? Why is AB in tension and BC in compression

A:

Q: The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by…

A: Given Data: The load on member is P = 1.4 kip. The cross-section area is A = 3 in ×5 in. The angle…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 9 mm².…

A: Given: The cross sectional area of rod 1A1=9 mm2=9×10-6m2 The cross sectional area of rod 2A2=18…

Q: The rigid bar ABD is connected to the rod BD which consists of a single bar with a width of 25,0 mm…

A:

Q: THE FRAME SHOWN CONSISTS OF FOUR WOODEN MEMBERS, ABC, DEF,BE, AND CF. KNOWING THAT EACH MEMBER HAS A…

A:

Q: Link BD consists of a single bar 1 in. wide and 12 in. thick. Knowing that each pin has a 38-in.…

A: The provided system is shown below.To determine: