7.) kilogram is defined as the mass that is accelerated at the rate of 1.0 ft/s^2 by a force of 1.0 lb. True False 8.) Newton (N) is defined as the force that accelerates a 1.0-kg mass at the rate of 1.0 m/s2 • True False 9.) A body is considered Rigid when the change in distance between any two of its points is negligible. True False 10.) Support reactions are considered external forces in structural theory. True False

7.) kilogram is defined as the mass that is accelerated at the rate of 1.0 ft/s^2 by a force of 1.0 lb. True False 8.) Newton (N) is defined as the force that accelerates a 1.0-kg mass at the rate of 1.0 m/s2 • True False 9.) A body is considered Rigid when the change in distance between any two of its points is negligible. True False 10.) Support reactions are considered external forces in structural theory. True False

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1/ Determine the magnitude and direction angle(0) of force (F4) So that the particle shown in figure (1) is in equilibrium? Fi-500 N F2=750 N 33 F4 30 60 F3=1200 N Figure (1)
I need ans within 8 minutes with draw happy emoji in the end my best wishes ton
U.S. AB= 21 Bc = I • CALCULATE THE • MOMENT OF INERTIA REACTIONS A (30k OF THE 20K BEAM MEXICO 2.5K/FT 17 20 B
Question 4: A machine of 540 kg is bolted at the middle of two parallel simply supported steel beams. The clear span of the beam is 2.4 m. The moment of inertia of the cross-section of each beam is I = 4.2×10¯6 mª. The Young's modulus of the steel is E 200 GPa. When the machine is operating, it will generate a vertical force P(t)=Posinot. When the machine runs at 300 rpm, Po= 1500 N. Neglect the weight of the beams and assume 2% viscous damping in the system. Determine the amplitude of steady-state deflection of the beams at their midpoint when the machine runs at 300 rpm. machine 1.2 m = 1.2 m Steel beams
The force R is the resultant of the other three concurrent forces shown. * The value of P is R 20° 30° 80 lb 100 lb 72.5 Ib O -72.5 Ib O 27.5 Ib O -27.5 Ib O None of the above O
Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the figure below where the horizontal force P = 155 N and the couple M = 573 Nm. M N m A 150 N 300 mm 250 mm PN 400 mm 90 N
A homogeneous disk with a radius of 9 in. is welded to a rod AG with a length of 18 in. and of negligible weight that is connected by a clevis to a vertical shaft AB. The rod and disk can rotate freely about a horizontal axis AC, and shaft AB can rotate freely about a vertical axis. Initially, rod AG is horizontal (0o= 90°) and has no angular velocity about AC. Knowing that the smallest value of 0 in the ensuing motion is 30°, determine (a) the initial angular velocity of shaft AB (b) its maximum angular velocity.
Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) A force F of magnitude 800 lb is applied to point C of the bar AB as shown. Determine: y-component of F (in lb)
5 Where does the resultant of the two forces act? 680 N 300 500 mm mm A 660 N Problem 2/85
6
The cantilever T- beam is loaded as shown in the figure. Ti 80 mm 40 kN/m NA 120 mm 20 m INa = 30x106 mm What is the reaction at the support in kN?
Problem 2-16 Resolve the force Fzinto components acting along the u and v axes and detemine the magnitudes of the components. Given: F1 = 250 N F2 150 N e1 = 30 deg 82 = 30 deg 83 = 105 deg