7. Determine completely the resultant of copianar concurrent force system shown in the figure. 500N 400N 407 30 300N 600N

Q: What is the cutting speed of turning in the unit of m/min, when main axis spindle speed is 2,409 rpm…

A: Given Data N=2409 rpm D=86 mm

Q: what is the cutting speed of a shaper having 80 strokes per minute with a length of a stroke at 1.25…

A: Given data, S = 80 stroke/min L = 1.25 feet = 15 in Find Cutting speed = V

Q: Part C - Radius of curvature for AB and BC Determine the radius of curvature for AB, PAB, and for…

A:

Q: I don't understand how they got answers from part d and e.

A: working fluid = mono atomic ideal gasto find (a) T3(b) heat input in constant volume prosess

Q: 2. Determine the moment about point C due to the forces shown. Note: 4 kips is perpendicular to the…

A: Given   Load, P1 = 2 kips             P2 = 4 kips Find  Moment of a force about point C

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: 2) Orthogonal Cutting: Consider a person who is shoveling snow from the sidewalk. This person can…

A: To find: The ratio of the force for shovel A to the force for shovel B.Given:Coefficient of friction…

Q: In which lathe operation, the cutting tool moves perpendicular and parallel to the axis of the…

A: Lathe is a two axis machine used to remove material from the workpiece.

Q: Question 1 Figure Q1a shows two cables attached to a half-ring anchor point as shown in Figure Q1a.…

A: 1-Use resultant formula of 2 force to solve first problem, 2- use equilibrium equilibrium to solve…

Q: GEOMETRY OF TECHNICAL DRAWING-TANGENCIES DRAW TANGENT TO CIRCLE AT PONT P AND TANGENT FROM Q TO…

A:

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Match each drawing to the term that describes it. Answers are used only once. NOTE: I asked this…

A:

Q: The following data are available from orthogonal cutting experimental. In this case: Thermal…

A: Solution:

Q: High tensile strength materials are cut by a single point cutting too with the negative rake angle

A: Yes ,High tensile strength materials are cut by a single point cutting too with the negative rake…

Q: 4. The drilling speed for cast iron is assumed to be 70 ft/min. Find the time required to drill two…

A:

Q: (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5…

A:

Q: QUESTION 1 Calculate the spindle speed in RPM of a lathe turning a 96 millimeter diameter material…

A: 1)

Q: To make 200 cast iron tool holders as shown in Figure 2 per order, two orders per year expected, and…

A: Consider the machining of harder material; this machining process induces high degree of stress and…

Q: Which one(s) of the following statements is true for limiting positions? Select all that apply.

A: In the four-bar mechanisms, the limiting positions cannot always be avoided. Hence statement (a) is…

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.