1. 2. Drill spot SR3 3. Countersink Knurl 4. Neck Spherical 5. Keyway 6. Spotface 7. Blind hole 8 Chamfer Counterbore 9 10. > > > > > 1. 2. Drill spot 3. SR3 Countersink 6 Knurl 7 4. Neck Spherical 5. 3 Keyway 2 6. Spotface 4 7 Blind hole 10 8. Chamfer 5 Counterbore 9 10. Ln co

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: Apply geometric tolerancing to part according to the instructions below. This exercise will provide…

A: The majority of current production techniques and equipment are incapable of producing items that…

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: Could ypu help me with this problem? It should start with something like this: P1=0,0 P2=10,0…

A: The part program for the given drawing uses the Fanuc Cut language. I'll start by identifying key…

Q: 360 degrees of crankshaft rotation. 1. A revolution is 720 2. The camshaft rotates degrees during…

A: To find :-  Fill in the blanks

Q: A) Draw the two limiting positions of the following crank-slider mechanism. Indicate all known sizes…

A: Given:To find:(a) Draw the two limiting positions.(b) Determine the piston stroke.

Q: F= 200 N %3D 30° 13 12 F2 = 260 N

A:

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Problem 7 Trekking handlebars or "butterfly bars" are popular with long-distance cyclists because…

A:

Q: Consider FIG-DD in the appendix.   Note: For Blocks “A” & “B” & “C”: The mass of “A” is 30 kg.…

A:

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: Compute the position and orientation of the tool point P from the given D-H table for the…

A: Given: Let us consider the given table with values, and the general transformation matrix,…

Q: The number of teeth on a gear is 27 and the outside diameter is measured as 10 mm. The module of the…

A: Given Data No. of teeth is 27 Outside diamtere is 10mm

Q: An engineer is creating a solid model of a simple gear using SolidWorks. Choose the correct…

A:

Q: A2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.