7. A closed-end, thin-walled cylinder of original length 1, thickness t, and internal radius r is subjected to an internal pressure p. If the Young's modulus is E and the Poisson's ratio is v, using the generalized Hooke's law equations, determine the change, if any, which occurs in the length of this cylinder when it is pressurized?

7. A closed-end, thin-walled cylinder of original length 1, thickness t, and internal radius r is subjected to an internal pressure p. If the Young's modulus is E and the Poisson's ratio is v, using the generalized Hooke's law equations, determine the change, if any, which occurs in the length of this cylinder when it is pressurized?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.2 A thin cylindrical shell, 1.5 m internal diameter, 2-4 m long, internal volume 4-23 m³, plates 25 mm thick, is under internal pressure of 1 N/mm². Assuming the end plates are rigid, find the changes in length, diameter, and volume. E=206,000 N/mm²; v=0.267.00 ART
A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 × 10-6 m³ when filled with a liquid at a pressure p. If E=200 GN/m² and v = 0.25, and assuming rigid end plates, determine: (a) the values of hoop and longitudinal stresses; (b) the modifications to these values if joint efficiencies of 45% (hoop) and 85% (longitudinal) are assumed; (c) the necessary change in pressure p to produce a further increase in internal volume of 15%. The liquid may be assumed incompressible.
4. A 200 mm long, stress free rod at room temperature is held between two immovable rigid walls. The temperature of the rod is uniformly raised by 250°C. If the Young's modulus and coefficient of thermal expansion are 200 GPa and ix10/ C, respectively, the magnitude of the longitudinal stress (in MPa) developed in the rod is
modulus of elasticity equal to 200x103 MPa and coefficient of thermal expansion equal to 11.7x10^-6/°C, the bottom is made up of brass with modulus of elasticity equal to 105x10^3 MPa coefficient of thermal expansion equal to 20.9x10^-6/°C. The temperature rose to 50°C from normal condition introducing stresses in the bar. Determine the force induced in the bar. T 250 530 mmm r so mm 300 mms
Q7: What is the compression in the tibia of lengthh = 30 cm of a person of mass m = standing erect? The bone is regarded as a hollow circular tube with internal radius r, = 1.2 cm and external radius r, = 1.75 cm, and Young's modulus along the axis is Y = 2 × 1010N/m². If the maximum tensile strength of tibia is 1.4 × 10®N/m², What is the compression in the tibia at the point of fracture? 80 kg %3D Fibula 1. Tibia
A steel (E=210 GPa, v=0.32) cylindrical vessel has a diameter R= 25 cm, thickness t=0.2 cm and length L=100 cm. What is the increase in the length of this vessel if it is subject to PR PR. an internal pressure P kPa (unit in kPa)? (Remember: o, =
For the prismatic bar in simple tension shown below, the stress state at any point "M" is characterized by Sig = p, and the other stress components are null. You are asked to determine the stress vector, as well as its normal and shear components, on a generic facet of normal parallel to the xy plane.
A gas is stored in a cylindrical tank of inner radius 7 m and wall thickness 50 mm. The gage pressure of the gas is 2 MPa. The maximum shear stress (in MPa) in the wall is
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 × 10-6 mm/mm/ °C). The cross-sectional area of bar (1) is A1 = 184 mm2 and the cross-sectional area of bar (2) is A2 = 380 mm2. After load P has been applied and the temperature of the entire assembly has increased by 38°C, the total strain in bar (2) is measured as 1240 µɛ (elongation). Assume L1 = 1290 mm, a = 590 mm, b = 820 mm, and L2 = 2000 mm. Determine: (a) the magnitude of load P. (b) the vertical displacement of pin A. L2 (1) L1 B a P Answers: (a) The magnitude of P = i kN. (b) The vertical displacement of pin A = i mm (down).
SM1007 THIN CYLINDER The pressure vessel shown.above is made from 4 mm thick steel plate. A pressure of 3.5 MN/m< is applied to the cylinder with a length of 1.1 m and an internal diameter of 0.3 m. Young's modulus is E = 220 GN/m2 and Poisson's ratio is v = 0.3.
V5
An enormous and expensive artwork with mass 42.8 kg is mounted on a wall with four heavy-duty steel bolts, each with a diameter of 5 mm. There is 10 cm gap between the painting and the wall. The shear modulus of the steel bolt is 9.0 x 10^10 N/‘m^2. Find the shear stress on the bolts and find the resulting vertical deflection of the bolts.