7 Mohr's normal and shearing stresses on the planes whose normals are at +60% 933. For the state of stress shown in Fig. P-933, determine and +150° with the X axis. Show these stresses on a sketch of the Ans. For 0 = 60°, a = 7.32 MPa and T = element. 10 MPa Y 20 MPa 10 MPa 20 MPa 10 Ma Flgure P-933. ذكرى بنان +مروة تقاعدين نقرا مقاومة بیت مروة C٥٠ ١٠٠۱۰ البت

7 Mohr's normal and shearing stresses on the planes whose normals are at +60% 933. For the state of stress shown in Fig. P-933, determine and +150° with the X axis. Show these stresses on a sketch of the Ans. For 0 = 60°, a = 7.32 MPa and T = element. 10 MPa Y 20 MPa 10 MPa 20 MPa 10 Ma Flgure P-933. ذكرى بنان +مروة تقاعدين نقرا مقاومة بیت مروة C٥٠ ١٠٠۱۰ البت

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The member is loaded as shown. The diameter of the member is 32 mm. 1) Calculate all internal loadings on the cross section through the point A. 2) Calculate the stress at point A due to each internal loading. 0.4 m A Rigid Wall 1000 N 300 Nm 2000 N
The stresses acting on element B (see figure part a) on the web of a wide-flange beam are found to be o = 11,000 psi in compression in the horizontal direction and oy = 2,600 psi in compression in the vertical direction (see figure part b). Also, shear stresses of magnitude Tzy = 3,200 psi, act in the directions shown. B Side Cross View Section (b) (а) Determine the stresses acting on an element oriented at a counterclockwise angle of 45" from the horizontal. Round your answers to one decimal place. psi psi psi
Q.b.
Calculate the value of Q and t that are used in the shear formula for finding the shear stress at A. 0.3 m 0.3 m 0.2 m 0.2 m 0.4 m 0.km 0.2 m
Find the normal stress value on the new x-axis obtained by turning 53 ° clockwise of the stressed element in the figure.
A thin triangular plate ABC is fixed on side AB. The plate is strained such that all straight lines in the plate remain straight after deformation and that apex C is displaced to point C'as shown. Compute the following: a) the normal strains ex, ey and the shearing strain yxy at point C based on small deformation theory b) the normal strain at point A in the direction of AC based on small deformation theory c) the normal strains ex, ey and the shearing strain yxy at point C based on large deformation theory A 30° -200 mm. 3mm C" 1 I 1 1 60° 4mm
A
Steel plate (2) b. 4. Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. a. 8.5 ksi 5.7 ksi 10.5 ksi Draw Mohr's circle for this state of stress. Me grapting page is ba b. Determine the principal stresses and the maximum in-plane shear stress acting at the point. Ans. c. Show these stresses on an appropriate sketch. <
(a) A steel structural member of length = 10 ft. is supported between two fixed supports so that it cannot expand. At 68°F, there is no stress in the member. (E = 30 x 106 psi and α = 6.5 x 10-6/°F) Calculate the stress (psi) in the member at 95°F. Stress (psi) = (b) If the same structural member is not supported between two fixed supports, calculate the total elongation of the member (in.) for the same temperature change. elongation (in.) =
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o- 29 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa O 42.4 MPa and -29.4 MPa O 26.2 MPa and -17.7 MPa O 53.1 MPa and -37.9 MPa O 45.4 MPa and -31.0 MPa O 34.1 MPa and -24.6 MPa