Determine the total length of the cable shown in meters, use two decimal points. -7 m-- 6 m--11 m-B16 mB(1)\ B3 = 35°21600 N2000 N

Calculating the reaction: ∑Fx=0HA=HB ...(a)∑Fy=0VA+VB=1600+2000 VA+VB=3600 ...(b)

Answered: -7 m |-6n 6 m -11 m A 6 m B (1) B2 B3 =…

Engineering

Civil Engineering

-7 m |-6n 6 m -11 m A 6 m B (1) B2 B3 = 35° (2) 1600 N 2000 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: block B weights 328 lbs, block C weighs 350 lbs, and block D weighs 300 lbs, what is the angle 0 of…

Q: Given: A0A1=10.250m B1B2=0.735m Determine the distance A1B2 in m

A: Here Reduction to MSL concept is using As height is increasing then readings is also increase to…

Q: Analyze the given cable below Determine the elevation of B using A as reference E 6m 20KN 1.5m C.…

Q: 25m B 200N 300 N 1.5m

Q: For the figure below, find the height of the water (H) needed to make the rectangular gate AB about…

A: Given :- Gate weight (w) = 343.35 KN Gate length (L) = 3 m Gate width (b) = 2 m The slope of the…

Q: In figure, if the floating ball radius is 0.5 m and its density= 2000 N/m3, the * ? cable tension is…

Q: Find the arc length and the tangent distance if the deflection angle is 50 25' 36" and the radius is…

A: Approach to solving the question:Please see attached photos for detailed solutions. Thank…

Q: Draw a sketch of level rods (as seen from the eyepiece of an engineer's transit) with the following…

A: (I) 2.245

Q: For adjusting the traverse, which of the following methods can be used? a. Compass traversing b.…

A: Option (D) is the correct answer.

Q: Q4 Parabolic cable of a 60 m portion of the roadbed of a suspension bridge are positioned as shown…

Q: In the figure, a uniform rod of mass m is hinged to a building at its lower end, while its upper end…

A: Given data: The angle at the lower end (θ1) = 54o tension in the rope = mg/2

Q: c.) 15.991 14.) A line was measured with a 50 m tape. There were 2 tallies, 8 pins and the distance…

A: 14. Tape Length = 50 m Measured distance = 2 tallies, 8 pins and last pin to the end…

Q: 1. Analyse a continuous beam and show the SF and BM diagram. k 35KN mmmmy (21 5m # B 80KN # с 辛 2m…

Q: 3. A line was measured by a 30m tape which was accurate before starting the day's work. After taping…

Q: he towers of the Golden Gate Bridge connecting San Francisco to Marin County are 1280 meters apart…

A: To find : Height of the cable 200 meters from a tower.

Q: 11-2 Why does a spiral improve the behavior of a column?

A: A spiral is a continuous winding of steel reinforcement in the form of a helix around the…

Q: maximum permissible cant

A: Given, Radius for a railway lines curved section R= 875 mLength,l= 200 mAllowable speed,V=100…

Q: road gauge railway line passes through a horizontal curved section (rac 200 m. The allowable speed…

A: Given data- Radius of curvature (R) = 875 m Length (L) = 200 m Allowable speed = 100 kmph Gauge…

Q: The true length of a line is known to be 200 m. When this is measured with a 20 m tape, the length…

A: Given, True length of line = 200m Measured length = 200.80m Designated length of tape = 20m

Q: 12. The slope of a ramp should not be more than: A. O 1 in 35 B. O 1 in 20 C. O 1 in 15 D. O 1 in 10

Q: A 100 m tape weighing 3 kg was standardized and found to be 0.02 m short at temperature of 10degC…

Q: Given the tension in cable CD is 10 kN the tension in cable CE is 8 kN Find • find the rectangular…

Q: angles subtended for the following conditions: a.* a 1-cm diameter pipe sighted by total station…

Q: I A Gunter's chain was used to take the follow- ing measurements. Convert these distances to feet…

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: The true length of a line is known to be 200 m. When this is measured with a 20 m tape, the length…

Q: Which of the following most nearly gives the approximate length of the cable in meters?

A: Length of the cable is given by : L= l+8h23l h- sag of cable l- span length of cable

Q: If the tension in cable CA is 50lb, determine the tension in Cable CD. Ba /45° 45 30 30 O 70.71lb…

Q: 2) Here, we see a different object hanging from ropes. If the object weighs 50lb, find the tension…

A: A system involving cables connected to each other through joints. The forces in cables are to be…

Q: Determine the following if P = 185 kN and Q = 120 kN. Use 4 decimal places and indicate only the…

Q: Compute the FR and ϴx on a 1 m wide strip of the gate shown.

A: Objective: To determine the resultant force on the gate and the angle made by the resultant with…

Q: Determine the correct length of a line reduced to the mean sea level when the recorded length with a…

A: Answer Correct length of a line is given by Correct length = Measured length - Total corrections…

Q: 5. The owners of a water park want to build a scaled-down version of a popular tubular water slide…

A: The distance between the points A and C is 140 feet. Use the distance formula to find distance or…

Q: -Xo

Q: should be the height (m) of a lighthouse, 50. What so that it can be visible from a distance of 3…

A: GIVEN : visible distance (d ) = 3 km TO FIND : height of light house ( h)

Q: 14. Describe the process of setting up a level. 15. The slope distance from point F to G is 245…

A: Note: As per guidelines and student requirement,I have solved 1st question only.

Q: ) Given that the height of a tower is 24.9048175127m, determine the length of the rope from the top…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Determine the total length of the cable shown in meters, use two decimal points.

-7 m-
- 6 m-
-11 m-
B1
6 m
B
(1)
\ B3 = 35°
2
1600 N
2000 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1:Calculating the reaction:

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the gradient from A to E if the distance between the two points is 80.56 m.
Q2: A stake is being pulled out of the ground by means of two ropes as shown. Knowing that a 5 308, determine by trigonometry (a) the magnitude of the force P so that the resultant force exerted on the stake is vertical, (b) the corresponding magnitude of the resultant 120 N 25° a
36.A broad gauge railway line passes through a horizontal curved section (radius = 875 m) of length 200 m. The allowable speed on this portion is 100 km/h. For calculating the cant, consider the gauge as centre-to-centre distance between the rail heads, equal to 1750mm, The maximum permissible cant (in mm, round off to 1 decimal place) with respect to the centreto- centre distance between the rail heads is
Please answer it. Thankyou
Fill in the blanks Smaller angle: Larger angle: s = 20 ft Determine the two possible angles so that the water strikes at B. VA = 40 ft/s 4 ft - 1 attachment - 8 ft
show complete solutions and original work please don't copy from other sites
analyze the cable shown
Q- A broad gauge railway line passes through a horizontal curved section (radius = 875 m) of length 200 m. The allowable speed on this portion is 100 km/h. For calculating the cant, consider the gauge as centre-to-centre distance between the rail heads, equal to 1750mm, what is the maximum permissible cant with respect to the centre-to- centre distance between the rail heads.
answer b, c, d please. Need complete solution, thank you! asap
Need asap. Ty
From the Figure below, calculate the distance (BC) if the distances d=15m and h=9m? B From the Figure below, calculate the distance (CE) if the distances CD=8m and DE=12m? 8m D 12m
Draw a sketch of level rods (as seen from the eyepiece of an engineer's transit) with the following measurements. 2.255 m 1.452 m 3.515 m 0.250 m 2.518 m i. i. iii. iv. V. Example: SDS