7-Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is transmitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components of reaction at the journal bearing C and thrust bearing D if 0= 0°. The bearings are in proper alignment and exert only force reactions on the shaft. 200 mm 250 mm 150N 300 mm 150 mm B So mm A 100N 120N

Q: Problem 1 Determine the reaction at A and C. Support at A is fixed, C is roller support, and B is…

A:

Q: From the frame loaded as shown. Solve the following if P = 15 P kN/m D 2P kN/m -8 m B H E 3P kN/m…

A:

Q: 5-54 The turbine develops 150 kW of power, which is trans- mitted to the gears such that both C and…

A: StressExplanation:Step 1:Step 2:Step 3: Step 4:

Q: Current Attempt in Progress The solid 27 mm diameter steel [E = 200 GPa] shaft supports two belt…

A:

Q: E F D A Describe the load path of the applied force (of the man's weight) to the reaction points.…

A: Solution Assume man's weight = W The load path is  Its free body diagram can be  drawn as

Q: 9-5. Determine the reactions at the supports, then draw the moment diagram. The moment of inertia…

A:

Q: - Reaction at A, shear at section 1---1, and moment at C. by using muller breslau principle. Write…

A: Muller Breslau principle it uses influence line diagram

Q: 9-11. Determine th B. El is constant.

A:

Q: Problem 1 An L-shaped bar is supported by a normal bearing at A and a smooth horizontal surface at…

A: Given data:- Below L-shaped bar diagram is given in question;

Q: 1. At the instant 0 Determine the angular velocity of the connecting rod BC & velocity of slider C…

A:

Q: Determine the moment about O Given T= 670 r= 20 cm B AngleTheta = 40 degrees The pulley at B is…

A:

Q: 4. Compute for the reaction at the roller B, the force components acting on the ball- and-socket at…

A:

Q: determine (a) the tension in the cable, (b) the reaction at C.

A:

Q: 1-5. The shaft is supported by a smooth thrust bearing at B and a smooth journal bearing at A.…

A:

Q: The bearings at A and D exert only vertical reaction on the shaft. The loading is applied to the…

A: A ) We are asked to determine : A ) The shear diagram for the shaft. B ) Draw the moment diagram…

Q: A Į - 6 m W B ·20

A:

Q: Determine the angle θ for equilibrium and investigate the stability at this position. The bars each…

A: The given figure is shown below. The given data is shown below:

Q: Current Attempt in Progress The solid 37 mm diameter steel [E = 200 GPa] shaft supports two belt…

A:

Q: The gear-pulling assembly shown consists of a crosshead CF, two grip arms ABC and FGH, two links BD…

A:

Q: The two forces are applied to the end of the boom OA. Determine the force F so that the resultant of…

A: Given:- The two forces are applied to the end of the boom OA The magnitude of one force = 200 lb The…

Q: A continuous beam carries the following loads. 12 kN/m 20 kN A 4m 3m 3m 1. Compute the moment at A…

A:

Q: #2 Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the…

A: Total length = 5+4+7+3 = 19

Q: The motor delivers 3000 hp to the shaft at 1500 rev/min, and efficiently transmitted to gear B and…

A: Given, P = 3000 hp  f = 1500 rpm  G = 77 GPa

Q: в с D E F G Hinge Hinge 4 m- - 4 m+3 m--3 m- 2 m 2 m a) Determine the maximum positive moment that…

A:

Q: IG =1.35 kg m coefficients of friction between the spool and the ground are 0.30 and 0.27,…

A: a.) Draw the free body diagram

Q: Problem 01 The beam is supported by hinged at A & D and roller at B & C. Determine the reaction at…

A: Given:- EI = Constant To find:- Reactions

Q: Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the…

A: Consider the figure,

Q: 6. The system below is fixed at A has a roller at C and contains a hinge a reactions at A and C so…

A: Given, The system is in equilibrium and the weight of the contraption is negligible  where A is…

Q: 2) An 8m bar hinged at the left end carries a 100N load 5m from the hinge support. The bar is also…

A:

Q: Draw the influence line for the vertical reaction at A. Use the analytical method in solving. Assume…

A:

Q: A 45 KN 8m -20 m 75 kN +4M. 2 30 kN B

A:

Q: 1) A system of three pin connected bars takes the depicted equilibrium position under the given…

A: Finding out forces in bars.