7-31. The bars of the truss each have a cross-sectionalarea of 780 mm?. If the maximum average normal stress inany bar is not to exceed 140 MPa, determine the maximummagnitude Pof the loads that can be applied to the truss.a9m-1.2m-1.2 m-0.75 P

Given Cross-section area 780mm2 Maximum allowable stress 140 MPa To find Maximum magnitude of P

Answered: 7-31. The bars of the truss each have a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bar has a cross-sectional areao of 490(10-6)m2. It is subjected to triangular axial distributed loading along its length which is 0 at x= 0 and 9 kN/m at x= 1.5 , and to two concetrated loads Determine the average normal stress in the bar as a function of x for 0 <_x < 0.6m
The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 14 mm. Assume L = 1.1 m and 0 = 20°. If the average shear stress in the pins at A, B, and C cannot exceed 125 MPa, determine the maximum distributed load Wmax that can be supported by the structure. (1) 0 Answer: Wmax i B kN/m C
A 25 mm square-cross-section bar of length 300 mm carries an axial compressive load of 50 kN. Determine the stress set up in the bar and its change of length when the load is applied. For the bar material E = 200 MPa
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.7 in.². Assume a = 3.25 ft and b = 3.90 ft. If the normal stress in each member must not exceed 35 ksi, determine the maximum load Pmax that may be supported by the structure. A B b b Answer: Pmax= kips
a b c d F 5 m 1.5 m 2.1 m 2.4 m 26 kN The structure above is subjected to a load at point C. Using the table below, determine the forces acting at the support pins and at pin B on member ABC. Forces: (Denote tension forces with positive values; compressive forces with negative values.) FAX = ? FAY = ?
The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the largest vertical load P that can be applied at C if the stress in the steel rod is limited to 35 ksi and the vertical movement of end C must not exceed 0.12 in. Neglect the weights of the members. L=4 ft A=0.5 in.2 E= 29 x 10 psi P. T-2 t 3 n ANSWER: Ib
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
If the allowable bearing stress for the material under the supports at A and B is ob = 670 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 3 in. by 3 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. P a Answer: Pmax= i b lb
The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied to it, determine the change in its length and the change in its diameter. Ep = 2.70 GPa, np = 0.4.
Determine the maximum force P that can be exerted on each of the two pistons so that the circumferential stress in the cylinder does not exceed 3 MPa. Each piston has a radius of 45 mm and the cylinder has a wall thickness of 2 mm.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

7-31. The bars of the truss each have a cross-sectional area of 780 mm?. If the maximum average normal stress in any bar is not to exceed 140 MPa, determine the maximum magnitude Pof the loads that can be applied to the truss. a9m -1.2m -1.2 m- 0.75 P