900 kg /m3C6iven:spherical drop lets act likeparti cles withdiame ter =0.020 mom settling through%3Dair at temperature= 3 1|. IS K and= 0.ImPapressuredensi ty uf single droplet= 900 kg /m3%3Dproperties of airdensity of air =viscosi ty of air = micro Pascal second:0.03921mol/dm319.01383SONE forterminal settlinag veloci ty.

Given data- Diameter of the particled=0.020 mm=0.0020 cmDensity of the particleρs=900 kg/m3=0.9…

6iven: Spherical drop lets act like particles with 0.020 mm sett ling through 311. IS K and diame ter = %3D air at temperature pressure = densi ty of %3D 0. Impa %3D single doplet : = 900 kg Im3 %3D properties of air density of air = mbl / dm3 viscosi ty of air = 19. 01383 micro Pascal · second 0.03921 Sowe for terminal settling veloci ty.

6iven: Spherical drop lets act like particles with 0.020 mm sett ling through 311. IS K and diame ter = %3D air at temperature pressure = densi ty of %3D 0. Impa %3D single doplet : = 900 kg Im3 %3D properties of air density of air = mbl / dm3 viscosi ty of air = 19. 01383 micro Pascal · second 0.03921 Sowe for terminal settling veloci ty.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the moment of inertia (in4) ĪY of the area shown with respect to the vertical line that passes to the centroid of the composite area if b = 5.8 in, h = 0.71 in, L = 7.49 in, and W = 0.77 in. Round off only on the final answer to expressed in 3 decimal places.
A joint is made by gluing two plywood gussets of thickness t = 0.56 in to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 12.65 in and the applied force is P = 7475 lb. Round off the final answer to three decimal places.
Give me right solution
Also determine the normal force excreted by the floor on each of his feet
Both ends of the beam are guided or slider support not Fixed support. Plz, solve this problem using stiffness Method and show all the step and alsi draw SFD and BMD My last two digits of my reg.no: 95 Structural Analysis-2
the value of A=382.3 , E=120 , B, 25 , AND D=9
How to get TEC and TBC
Q2: Determine (Y). If PA - Pg = 6624 %3D 40 Marks Water Water Mercury 6Y
Engineering Mechanics DETERMINE THE INTERNAL FORCE OF MEMBER DF FROM THE FIGURE BELOW. Note: for compression, include a negative sign ( - ) and for tension, type answer as is. Use four (4) decimal places during computation and two (2) decimal places for the final answer.
Engr. Sova Ho used 30m length of tape in measuring a distance line. The measured length of the line was recorded to be 454.62 m. During the measurement the temperature reading was 11 oC and the tape was supported at both ends. The cross sectional area of the tape is 6.50mm2 and the modulus of elasticity is 200 GPa. The tape has a weight of 0.075 kg/m. K= 11.6 x10-6 m/c. If the engineer determined the Temperature correction, Pull correction, and Sag Correction lengths to be 1,640.01 μm, 588μm, and 1.71 mm respectively, per segment. Calculate the applied Pull of the 30m tape in kg.
answer f3 and p only