6/49 The 2-kg collar at C has an outer diameter of 80 mm and is press fitted to the light 50-mm-diameter shaft. Each spoke has a mass of 1.5 kg and carries a 3-kg sphere with a radius of 40 mm attached to its end. The pulley at D has a mass of 5 kg with a centroidal radius of gyration of 60 mm. If a tension T = 20 N is applied to the end of the securely wrapped cable with the assembly initially at rest, determine the initial angular acceleration of the assembly. Neglect friction in the bearings at A and B and state any assumptions. 300 mm 300 mm 200 mm 400 mm 40 mm 3 kg B T 100 mm

6/49 The 2-kg collar at C has an outer diameter of 80 mm and is press fitted to the light 50-mm-diameter shaft. Each spoke has a mass of 1.5 kg and carries a 3-kg sphere with a radius of 40 mm attached to its end. The pulley at D has a mass of 5 kg with a centroidal radius of gyration of 60 mm. If a tension T = 20 N is applied to the end of the securely wrapped cable with the assembly initially at rest, determine the initial angular acceleration of the assembly. Neglect friction in the bearings at A and B and state any assumptions. 300 mm 300 mm 200 mm 400 mm 40 mm 3 kg B T 100 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 740 kg and an average gear-tooth force of 2.60 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset X of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assumer = 110 mm, R= 695 mm, 0 = 24° Detail of contact at B Answer: X mm
5kg plate, and 3 kg slender rod. FIND, the radius of gyration of the pendulum about an axis perpendicular to the screen and passing through the point G.
4
The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k and the spring is unstreched when theta= 80 degree.if W=kL the bar has three equilibrium position in the range of 0
The motor causes the aluminum shaft containing gears D, E, and F to rotate. The solid shaft has a diameter of 24 mm and a modulus of rigidity of 24 GPa. The bearings at G suddenly jams, after which gear B rotates an additional 0.27 radians and gear C rotates an additional 0.21 radians. Determine the resulting torsion, T, that must be occurring in the shaft between gears D and E. Assume that D and E are rotating the same direction. Also note that gears B and C both have a 60 mmtradius. Express your answer in Nm to the nearest whole Nm. 100 mm 30 mm 60 mm D. 40 mm 0.8 m 0.4 m 02 m 0.2 m
2m dz - m. None of them اپن For the robot above, please determine Uo (the potential energy of Link #0) OU 9.8 OU = 5.6 OUo = 4,9 OU=19.6 * d₁, d₂ and ₂ are the joint variables m₂ = m₁ = m₂ = m₂ = 1 kg The moment of inertia of the last link is 3 kg.m². The mass centers are located on the middle point of each link.
The shaft, lever, and handle are welded together and constitute a single rigid body. Their combined mass is 21 kg with mass center at G. The assembly is mounted in bearings A and B, and rotation is prevented by link CD. Determine the magnitudes of the forces exerted on the shaft by bearings A and B while the couple is applied to the handle as shown. Would these forces change if the couple were applied to the shaft AB rather than to the handle? 535 mm. 280 mm Answers: A- B- 355 mm 280 mm 125 mm D 405 mm 37N-m 405 mm 235 mm N N D
Problem Statement Based on Problem 5-74 from the textbook. The bend rod is supported at A, B, and C by smooth journal bearings. Determine the components of reaction at the bearings if the rod is subjected to the force F. The bearings ar ein proper alignment and exert only force reactions on the rod. F=815m d=1.00m e=1.90 m f=2.20 m 30° 60° B d f 0.75 m
A force of P = 20 N is applied to the cable, which causes the 175-kg reel to turn without slipping on the two rollers A and B of the dispenser. Neglect the mass of the cable. Each roller can be considered as an 18-kg cylinder, having a radius of 0.1 m. The radius of gyration of the reel about its center axis is kg = 0.42 m. (Figure 1) Figure 30% 250 mm OG 500 mm A o OB 400 mm-
The 900 lb electrical transformer with center of gravity at G is supported by a pin at A and a smooth pad at B (like a rocker). The vertical component of reaction at the pin A is. 1.5 ft A 3 ft °G B
The position of the head and neck and the forces acting on the head are shown in the figure. The center of gravity of the head of mass m=9 kg is located at point C. The joint reaction force of F J = 150 N, which makes an angle of α = 30° with the vertical from the point B, is acting on the skull by the neck extensor muscles. The center of the atlantooccipital joint is located at point B. For this flexion position of the head, the neck muscle force FM, which makes an angle of γ with the horizontal from the point A , is effective . (Take the gravitational acceleration g as 9.81 m/s 2. ) Accordingly; a) Calculate the angle γ of the muscle force F M with the horizontal. b) Calculate the muscle strength F M. (Write your result in N units.)
6-76 The triangular plate of uniform thickness shown in Fig. the two cables supporting the plate and the reaction at the ball support. has a mass of 400 kg. Determine the tensions in 900 mm B 1500 mm y