63 : A steel wire of diameter 1 x 10³ m is stretched by a force of 20 N. Calculate the strain energy per unit volume. Y for steel is 2 x 1011 N/ m?.
Q: Q1: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN.…
A:
Q: A circular rod of cross-sectional area 2 x 104m² has a tensile force of 80 kN app The stress in the…
A:
Q: The five-bolt connection shown must support an applied load of P = 480 kN. If the average shear…
A:
Q: a) Sketch a stress-strain diagram for a metal indicating the proportional limit, yield point,…
A:
Q: 5. An A36 W-beam steel guardrail has an allowable strength of 165MPa and E = 200GPa. The W-beam…
A:
Q: Assume a person's mass is 54.0 kg and each of her shoes has an area of 195 cm². F on her feet if her…
A:
Q: 1. A frame ABC shown in Figure 2 consists of a tension member AB and a compression member BC. Member…
A: Given that Mdulus of elasticity,E=200 GPa=200×109Pa Horizontal force,H=150 kN=150×103N Length,L=3.5…
Q: A circular rod of cross-sectional area 2 x 10m² has a tensile force of 80 kN applied to it. The…
A:
Q: A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal…
A:
Q: A tensile stress is to applied along the long axis of a cylindrical brass rod that has a diameter of…
A:
Q: A 2 m long steel rod has a cross-sectional area of 0.3 cm?. The rod is a part of a vertical support…
A: The stress of the rod is given by F/A Strain is given by dL/L where F= Force…
Q: Two wires have lengths in the ratio 4 : 3 diameters in the ratio 2 : 1. Calculate elongations…
A: To find-Ratio of elongations x1 : x2Given data-Y1 : Y2=1 : 2,L1 : L2=4 : 3d1 : d2=2 : 1
Q: The steel rod with a diameter 15 mm is applied by a load of 15KN due to the load the diameter of the…
A:
Q: Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the…
A: Given data: Observe from the diagram, Total displacement of layers D = 2 mm Height of stripe L = 5…
Q: 1. a) Sketch the stress-strain graph for a typical ductile material under tension, labelling the…
A:
Q: Example: A lever is keyed to a shaft 38mm diameter (Ø) the width of the key is 13mm and its length…
A: a = 0.915 m d = 38 mm = 3.8 cm = 0.038 m r = d2 = 3.82 = 1.9 cm = 0.019 m w = 13 mm = 0.013 m l = 50…
Q: P-1. A steel shaft 2 m long that has a diameter of 90mm. is subjected to a torque of 10 KN-m. Use G…
A: Given data d=90 mmT=10 kN-mG=200 GPa Here, d is the diameter and T is the torque. While G is the…
Q: Q2c) Listed in the table below is the tensile stress-strain data for different grades of steels.…
A: Given Listed in the table below is the tensile stress-strain data for different grades of steel, as…
Q: Calculate the work done in stretching steel wire of length 2 m and of cross sectional area 0.0225…
A: To find-Work done (W)=?Given-Length (L)=2 mArea (a)=0.0225 mm2=0.0225×10-6 m2Load (F)=100 NYoung's…
Q: Review Problem. A 36.0 kg hammer strikes a steel spike 2.20 cm in diameter while moving with speed…
A:
Q: Q2: A conveyor beam has the cross section shown below and it is subjected to a be moment. Determine…
A: Solution:- Given data; Area (1) =25×150=3750 mm2…
Q: The rigid bar A,B,C shown in figure is connected to to a steel bar at A, Aluminum bar at B. the…
A: Using compatibility relation, ∆A7=∆B3=∆D33∆A=7∆B∆B=∆D Take moment about c,…
Q: EXample 2: the ankle joint therefore pushes upward on the bottom of the tibia with the force of 2800…
A: Given : R1=1.3 cmR2=2.5 cm
Q: Mechanical engineering question. Need diagram and explanation. No chatgpt.
A: Step 1: Step 2: Step 3: Step 4:
Q: H.W/assume a leg has 0.6m shaft of bone with an average cross sectional area of 1.5 cm.What is the…
A:
Q: The figure shows an approximate plot of stress (10° N/m2) versus strain for a thread that will break…
A: Stress versus strain graph is given for a thread. the stress is plotted along y axis and the strain…
Q: The figure shows the stress versus strain plot for an aluminum wire that is stretched by a machine…
A:
Q: Find the modulus of elasticity of a brass rod of cross section 20 mm x 20 mm and length 250 mm…
A: Cross section Area, A = 20x20 mm2 A= 400 X 10-6 m2 Length, L = 250…
Q: 3. The length of the biceps muscle increases 1.7cm over the course of an overhead softball throw.…
A:
Q: A 1.8 x 10-3-kg house spider is hanging vertically by a thread that has a Young's modulus of 4.0 x…
A:
Q: Q2: The 20-mm-diameter bolt fastens two wooden planks together. Find the smallest thickness of cach…
A: Given, Diameter is 20 mm and working bearing stress for wood is 13 MPa
Q: A hole is to be punched out of a plate having a shearing strength of 40 ksi. The compressive stress…
A: Solution:-Given thatSharing strength of plate (τs)=40 ksi=40×103 pound/in2Compressive strength of…
Q: Two wires of the same material (Young's modulus Y) and same length L but different radii R and 2R,…
A: Given that The length of the wires is same. But the radius of the first wire is 'r' while of other…
Q: Problem 6: The assembly shown below consists of 30 mm diameter aluminum bar ABC with fixed collar at…
A:
Q: Proof that the energy stored in the compact bone is given by E = AL0 (Sb) ^ 2 / 2γ. When Sb is bone…
A:
Q: Q4. When a tensile load (F) is applied to a solid homogeneous rod, the rod undergoes a change in…
A: Write the basic expressions related to stress and strain. Here, σ represents the stress, A…
Q: B/ A four fifth meter long steel pipe has an inside and outside diameter of 24 mm and 30 mm…
A:
Q: 10. Young's Modulus for steel is 2.1 x 1011 Pa. A steel cable will break if it is subjected to a…
A: Young's modulus (Y) = 2.1×1011 PaArea (A) = 1.5×10-5 m2Length (L) = 18 m maximum stress = 3000 MPa
Q: Q. 8: Strain energy per unit volume is given by 1 (stress)? 1 (b) 2 * (stress)* y (a) 2 y 1 strain 1…
A: We know, Strain is produced in the wire due to application of load. Hence. work is done on…
Q: ID 5t1 5t Part A Determine the negative bending moment at A with the maximum magnitude. Express your…
A: The force which applied to any material to cause deformation or bending along the plane or parallel…
Q: wire has a cross sectional area ‘A’, length ‘L’ and young’s modulus ‘Y’. It is pulled by a force ‘F’…
A: Given: Cross-sectional area = ‘A’, length = ‘L’ young’s modulus = Y It is pulled by a force ‘F’…
Q: A sphere of copper has a radius of 8.00 cm and is compressed uniformly by a force of 5.00 × 108 N.…
A:
Step by step
Solved in 2 steps
