60 uniform loading of 200 N/m. If the weight of the cable is neglected and the slope angles at points A and B are 30° and 60°, respectively, determine the curve that defines the cable shape and the maximum tension developed in the cable. 200 N/m -15 m

60 uniform loading of 200 N/m. If the weight of the cable is neglected and the slope angles at points A and B are 30° and 60°, respectively, determine the curve that defines the cable shape and the maximum tension developed in the cable. 200 N/m -15 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cable is subjected to a uniform loading as shown. If the slope of the cable at point O is zero, determine 1. the equation of the curve, 2. the tensile force in point O, 3. the tensile force in point B. CABLE.png y B 8 ft 500 lb/ft 500 lb/ft 15 ft 15 ft
Determine the magnitude (N) of the force in cable AD.Determine the magnitude (N) of the force in cable AC.Determine the magnitude (N) of the force in cable AB.
The cable AB is subjected to a uniform loading of 160 N/m. If the weight of the cable is neglected and the slope angles at points A and B are 20° and 70°, respectively, determine the maximum tension developed in the cable in kN. 70° 20° 160 N/m -15 m
Properties of cable CF: A 50 sq. mm. E = 90 GPa L1 Determine the following: A. Tension of cable BE = B. Tension of CE = C. Stress of cable BE = D. Stress of cable CF = E. Change in length of BE = F. Change in length of CF = G. Vertical deflection of point B = H Vertical deflection of point C = A bar ABC which partially carries a uniform load of W = 15 kN/m is being supported by two cables BE and CF. The segments of the bar have lengths: L1 = 1 m, L2 = 2 m, and L3= 1 m. Take note the vertical cable has a length of H = 2 m Properties of cable BE: A = 20 sq.mm. E = 100 GPa N N MPa MPa mm L2 mm mm L3 mm с
The cable AB carries a tension of 280 N. Determine the moment about O (positive if counterclockwise, negative if clockwise) of this tension as applied to point A of the slender bar.
Problem 2.41: Determine (a) the required tension in cable AC, knowing that the resultant of the three forces exerted at point C of boom BC must be directed along BC, (b) the corresponding magnitude of the resultant. D 65° 25° 50 lb 75 lb
3. If the plate is to remain in equilibrium, find the tension for all the three cable that supports the plate weighing 2200kg.
2. A cable 300 m long weigh5 600 N. The tension at the emds of the cable are 400 N and 446 N, respectively. (Note: Treat this as catenary). a) Determine the difference in elevation of the supports at both ends. b) Determine the difference in elevation of the lowest point and the lower support. c) Compute the horizontal span of the cable. T= 446 N Tz= 400 N S2 X2 L
The cable AB is subjected to a uniform loading of 200 N/m. If the weight of the cable is neglected and the slope angles at points A and B are 30° and 60°,respectively, determine the curve that defines the cable shape and the maximum tension developed in the cable.
b) Two cables are tied at ring 0 on the bent pipe supported by a hinge at O as shown in Figure Q1b where the elbow at A forms a right angle (i) Knowing that the tension In cable BC Is TBC = -164.0/ + 379.1/+98.9k N and that the tension in cable BD has the magnitude of 510 N. determine the resultant force R of the tension by the two cables at ring B. (ii) If the ring at B also supports the load of mass m and another tension T3 applied in the z-x plane, determine the tension Tj and the mass m for which ring B is in static equilibrium. Omit the reaction in section AB of the pipe and use TBS=164.8/ + 379.1/+ 98.9k N and TBD=192.1/+388.4/- 268.9k N. c) For the bent pipe in Figure Q1b and without any detailed calculation, evaluate the reaction at the elbow A. 1.35 m 1.5 m 0.3 m 1.1 m -0.9 m 1.2m I
Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension T in cable CD?